Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Boxster 1999 : fuel gauge spinning


Recommended Posts

Hello,

As from today my 2.5L Boxster's fuel gauge started spinning.

The fuel gauge needle jumps from one side of the gauge to the other side.

This morning when the fuel tank was half filled the needle indicated O liter (fuel tank empty), when turning the ignition off the needle went to 1/4L. Again ignition on and the needle stayed at 1/4L.

After filling up the tank it became worse. The needle just climbed up until it touched the temperature gauge needle...!

When turning the ignition off and on again I took some pictures (see attachment, these 5 pictures were taken in about 30 seconds).

I did not check anything yet. I only disconnected the battery to 'reset' the instrument but this did not help.

The needle never returns to '0' when turning the ignition off.

Has anyone experienced such phenomenon and can you give me a hint to find the root cause.

Is it possible that a poor mass connection causes this problem? (I doubt it because all other functions of the instrument work fine, also the measured distance to go and also the average fuel consumption seem to work as the temperature gauge does).

Thank you for reactions,

Alfred / Belgium

jumping_fuel_gauge_needle.PDF

Edited by Loren
Removed 30 MB download
Link to comment
Share on other sites

Loren,

thanks for the quick response.

I'll check the fuel sensor tomorrow. I found some 'Ohm-values' on a German Porsche website.

But I still wonder why the needle stays activated with ignition 'off'.

There is a company in Germany which is specialised in repairs of ECU's and Instrument clusters. In the worst case I have to send the unit to them.

Nevertheless if you or somebody else has a hint, then I would appreciate to hear it.

Regards,

Alfred

Link to comment
Share on other sites

Loren,

I read in the shop manual that a calibration of the fuel level sensor might be necessary wit the PST2 or PIWIS when the battery, cluster or fuel level sensor have been disconnected.

Unfortunately this feature is not covered with the Durametric Tool...

Is it possible to arrange a so-called 'manual self calibration' i.e. by filling and driving the fuel tank empty repeatedly or disconnecting the battery at a certain fuel tank content ?

Regards,

Alfred

Link to comment
Share on other sites

Hello Loren, Toolpants,

My fuel gauge seems to be defect.

I have a spare cluster with speed indication in miles instead of kilometers.

Do you think it is feasible to replace the NOK-fuel temperature gauge and the fuel gauge by an OK-one separately, since I think they are similar on both versions.

I saw a picture of a dismantled cluster somewhere else on the site.

Is the dismantling self-evident and can I find somewhere a description with fotos or pictures ?

Thanks,

Alfred

Link to comment
Share on other sites

  • 7 months later...

Hello Loren and other forum members,

My fuel gauge problem is not solved yet.

I attached a picture to explain what happens :

- the fuel gauge needle stays beyond the 'FULL' mark. When turning the ignition on then the needle starts to jump up & downwards some mm's and then remains above the 'FULL' mark.

- the board computer seems to work fine since the 'RANGE' follows the content of the fuel tank.

- when the fuel tank is nearly empty, the 'RESERVE' indicator telltale lights up.

This makes me believe that the fuel gauge is working correctly (I already measured the resistance with the tank full and nearly empty and this seems OK to me).

Replacing the instrument did not help either.

Do you think that a calibration with the PST2 would cure the problem taking into account that the OBC and the 'RESERVE'telltale work correctly?

Additional information :

1. All other functions of the instrument panel work fine.

2. with the Durametric Diagnostic Tool I have no access to the instrument panel although I can communicate with all other computers (ABS, engine, HAVC, alarm,).

Therefore I rather suspect a ground or cable problem.

Any useful hint would be welcome !

Thanks

Alfred

post-827-1194203254_thumb.jpg

Link to comment
Share on other sites

Loren,

Indeed, the sympton is the same with an other instrument panel, so I exclude an internal defect in the instrument panel itself.

After changing the instrument panel, I installed my genuine one back in the car and then I had the similar phenomenon with the RPM-counter and with the speedometer (they both jumped to the max. values and stayed there ...!).

Then I dismantled everything again and noticed that one of the lugs of the instrument panel assy was not fully engaged. After correcting this the RPM-counter and the speedometer functioned normally again.

Only the problem with the fuel gauge remains...unsolved.

Would appreciate any further suggestion...

Alfred

Link to comment
Share on other sites

  • 6 months later...

Hello,

My problem is solved at the end !!

I wrote that I tried a second instrument panel which showed the same failure (although the needle gauge was in the '0' position before I installed the instrument in my car).

Fortunately I got today the opportunity to try-out a third instrument panel and everything functions perfectly now.

Conclusion : MURPHY must have been hidden in the 2nd instrument panel. Those things happen and as we know : never say 'impossible'...

Thanks to all of you who gave me hints to locate the problem cause.

Alfred

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.