Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

'08 Boxster S - airbag removal question


Recommended Posts

I am removing the Black airbag and replacing it with a Red one. It has the "sport" steering wheel and I understand there are 2 screws holding it in place, on the rear. What kind of tool do I need to remove it? I am not the mechanical type but maybe this is something I can do myself (?).

Thanks in advance...Bob Z.

Link to comment
Share on other sites

Bob, whatever you do, don't have the key in the ignition when working on the airbag.

Roger that! I found some instructions online but they don't describe what kind of tools I need. It also states that the battery be disconnected.

Thanks...Bob Z.

Link to comment
Share on other sites

Whoever told you there are two screws must have one missing themselves. The airbag is held in place by a spring clip that locks onto three points on the rear of the airbag. To release the spring from the three points you simply insert a long flat bladed screwdriver in the small hole on the bottom of the wheel on the rear side. Push hard against the spring resistance and the airbag simply unclips.

You need to put the key in the ignition (in the off position) before disconnecting the battery to ensure the alarm doesnt go off and so that the steering lock is disabled allowing you to turn the wheel.

Its easier if you turn the wheel by about 90 degrees so the hole in the rear of the wheel sits horizontal rather than facing towards the seat and floor.

Once the airbag is unclipped you need a small flat bladed screwdriver to remove the center locking lug from the yellow and green connectors on the rear. The connectors cam then be pulled out of the airbag along with the smaller black clip.

All told , you can swap and airbag in under 20 mins once you've done it a few times.

Link to comment
Share on other sites

Whoever told you there are two screws must have one missing themselves. The airbag is held in place by a spring clip that locks onto three points on the rear of the airbag. To release the spring from the three points you simply insert a long flat bladed screwdriver in the small hole on the bottom of the wheel on the rear side. Push hard against the spring resistance and the airbag simply unclips.

You need to put the key in the ignition (in the off position) before disconnecting the battery to ensure the alarm doesnt go off and so that the steering lock is disabled allowing you to turn the wheel.

Its easier if you turn the wheel by about 90 degrees so the hole in the rear of the wheel sits horizontal rather than facing towards the seat and floor.

Once the airbag is unclipped you need a small flat bladed screwdriver to remove the center locking lug from the yellow and green connectors on the rear. The connectors cam then be pulled out of the airbag along with the smaller black clip.

All told , you can swap and airbag in under 20 mins once you've done it a few times.

Perfect, and it appears that even I can do it myself - thanks! I'll be sure to post the results and a pic when I am done; however, the Red airbag has to come from Germany, on a slow boat.

Link to comment
Share on other sites

Whoever told you there are two screws must have one missing themselves. The airbag is held in place by a spring clip that locks onto three points on the rear of the airbag. To release the spring from the three points you simply insert a long flat bladed screwdriver in the small hole on the bottom of the wheel on the rear side. Push hard against the spring resistance and the airbag simply unclips.

You need to put the key in the ignition (in the off position) before disconnecting the battery to ensure the alarm doesnt go off and so that the steering lock is disabled allowing you to turn the wheel.

Its easier if you turn the wheel by about 90 degrees so the hole in the rear of the wheel sits horizontal rather than facing towards the seat and floor.

Once the airbag is unclipped you need a small flat bladed screwdriver to remove the center locking lug from the yellow and green connectors on the rear. The connectors cam then be pulled out of the airbag along with the smaller black clip.

All told , you can swap and airbag in under 20 mins once you've done it a few times.

Perfect, and it appears that even I can do it myself - thanks! I'll be sure to post the results and a pic when I am done; however, the Red airbag has to come from Germany, on a slow boat.

I just re-read the above posts - what is the order for the battery disconnect & key removal? There seems to be a conflict in what people have posted.

Link to comment
Share on other sites

You do not remove the key from the ignition , just make sure that the key is not in the "ON" position , ie there are no lights on the dash before you disconnect the battery. Leave the key in the ignition until the battery is reconnected. I know this becuase I've fitted the multi function wheel controls on one occasion and a complete new wheel on a second occasion. These are the procedures in the workshop manual.

If you do not put the key in the ignition the alarm will sound on disconnection and reconnecting the battery . You will not be able to rotate the wheel once the battery is disconnected if the key is missing from the ignition , so you must make sure the wheel is positioned first so you can get to the airbag release mechanism. Unless there is something wildly different with the sport wheel it should be the same procedure as other 987/997 vehicles.

Edited by berty987
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.