Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

I hope someone can help.  Recently bought a 2011 C2S.  Memory setting for 'key button 1'  and 'person buttons 2.3' do not work.  Following Owner's Manual instructions, but get no "beep" or any other indication that settings were saved.  Pushing buttons results in nothing.  I move seats all over, make the 'save' and nothing works when I press the buttons.  Is there a trick I do not know, or is something broken?  Thank you.

Link to comment
Share on other sites

How about key #2?  Does it have same behavior as key #1 with the three buttons?  I get the confirmation beep each time, all three buttons and each key. 

 

If key #2 has the same problem, maybe there is a bad fuse for the comfort settings.  If you have access to a Durametric you could try to see if there are any codes or a reset.  Outside this it may be a dealer trip is warranted. 

Link to comment
Share on other sites

  • 1 month later...

I hope someone can help.  Recently bought a 2011 C2S.  Memory setting for 'key button 1'  and 'person buttons 2.3' do not work.  Following Owner's Manual instructions, but get no "beep" or any other indication that settings were saved.  Pushing buttons results in nothing.  I move seats all over, make the 'save' and nothing works when I press the buttons.  Is there a trick I do not know, or is something broken?  Thank you.

 

I had exactly the same problem. Turns out the CAN bus control module which controls the key memory and light at the bottom of the door was loose / disconnected (behind the door card I think). If your door light does not work that's a pretty good sign that you have the same (or similar) problem.

Link to comment
Share on other sites

 

I hope someone can help.  Recently bought a 2011 C2S.  Memory setting for 'key button 1'  and 'person buttons 2.3' do not work.  Following Owner's Manual instructions, but get no "beep" or any other indication that settings were saved.  Pushing buttons results in nothing.  I move seats all over, make the 'save' and nothing works when I press the buttons.  Is there a trick I do not know, or is something broken?  Thank you.

 

I had exactly the same problem. Turns out the CAN bus control module which controls the key memory and light at the bottom of the door was loose / disconnected (behind the door card I think). If your door light does not work that's a pretty good sign that you have the same (or similar) problem.

 

 

 

BTW, I assume that you held the "1" (or 2 or 3) key while pressing the "M" (Memory) button to save the setting(s) ?

Link to comment
Share on other sites

  • 4 years later...

 

On 8/11/2014 at 11:15 PM, systech said:

 

I had exactly the same problem. Turns out the CAN bus control module which controls the key memory and light at the bottom of the door was loose / disconnected (behind the door card I think). If your door light does not work that's a pretty good sign that you have the same (or similar) problem.

 

I have similar problems: white lights in doors flickering; passenger-side window doesn't auto-up, sometimes doesn't auto-down; reverse mirror setting can't be changed; and key programming can't be changed. Do you know how to access and check the fitment of the CAN bus control module? Has anyone identified other culprits for these problems? Also, the after market Dynavin stereo seems to spontaneously power down.

Edited by pavinpavin
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.