Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

Before I tackled this job on my 2008 Cayenne base I read and read to make sure I had everything, however I have hit a bump in the road....my rear caliper bolts do not seem to be 16mm triple square.

 

I purchased a Kommen 16mm triple square socket (part number KM117-A) and it is too big.

 

My question is: Was there another size used in 2008? Maybe just on the V6 models? Anyone know what it is?

 

Thank you.

Link to comment
Share on other sites

It doesn't look like the brakes were ever apart. It has about 50k on the clock and my sensor went off indicating replacement.

 

This is what I bought:

 

http://www.kommentools.com/products/transmission-drain-plug-socket-audi-a3-a4-a6-vw-golf-tri-square-16mm

 

There was no way it was fitting in. At least it didn't seem that way. It seemed way to big. I would place it on the bolt and turned it slowly to see if it would catch but it didn't want to drop in.

Link to comment
Share on other sites

Well I finally picked up a T50 torx bit to get those pesky rotors off up front. After I did the fronts, and since I was already filthy I decided to slide under the car to get a good look at the rear caliper bolts.

 

The tool I purchased (listed above) is too big. Plain and simple its not right. Now according to the number written on the tool it is a 16mm triple square.

 

So now I guess we have two possibilities....

1. The tool is mis-marked

2. My 2008 Cayenne base has rear caliper bolts that are triple square but are smaller than they are supposed to be.

 

Looks like a triple square kit is in order.

Link to comment
Share on other sites

The first time I tried it I had the wheel off and was ducking into the wheel well trying to fit the tool into the bolt. I could see the bolt, just not the center of it. I ran out of time and had to put everything back together.

 

The other day I actually slid under the car so I was staring straight at the face of the bolts. They are definitely triple square. The tool I have (listed above) is big enough to cover the hole in the bolt. I should be getting a kit of 4 triple squares (10mm, 12mm, 14mm & 16mm) on wednesday and will see if my original tool is maybe mis-marked or if the openings are really smaller than 16mm.

 

If I had to guess, and without having a 16mm or a 14mm in front of me, and assuming that my tool that I have is actually a 16mm, then I would not be surprised if they are 14mm

Link to comment
Share on other sites

  • 2 weeks later...

Well I have an answer.......

 

I ordered a set of 4 triple squares from Sears (Schwaben....very nice by the way) to see if maybe the bolts were 14mm instead of the 16mm. The answer is.....nope. They are 16mm. The Kommen 16mm triple square socket (part number KM117-A) that I got from EBAY was either not manufactured correctly or was some cheap chinese knock off. The Schwaben 16mm fit perfectly. When I had the bolts out I tried to fit the Kommen and it was a no good. It was just too big.

 

On a side note I can say that those rear brakes are a pain. Not impossible but certainly not as easy as most.

Link to comment
Share on other sites

  • Moderators

 The Kommen 16mm triple square socket (part number KM117-A) that I got from EBAY was either not manufactured correctly or was some cheap chinese knock off. The Schwaben 16mm fit perfectly. When I had the bolts out I tried to fit the Kommen and it was a no good. It was just too big.

 

 

 

Yet another example of why not to buy cheap or poorly made tools...............

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.