Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

DIY Throttle Body cleaning

Orient Express
 Share

Recommended Posts

  • Moderators
Orient Express Member

Orient Express

Posted
  • Moderators
Posted

DIY Throttle Body cleaning

One of the problems that I see with many 996/986/997/987 owners complaining about is a lumpy or erratic idle and sometimes sluggish acceleration. I have a quick cure for this problem. In fact, this cure will work for any car that has a throttle body. The issue is that over time a sludgy gunk will build up in the throttle body where the throttle butterfly opens and closes. This gunk will eventually change the airflow characteristics of the gap between the butterfly and the throttlebody

 

Link to comment
Share on other sites
  • 8 months later...
gofor28off Member

gofor28off

Posted
Posted (edited)

I performed this service and now I have a "noise" when I quickly blip the throttle at idle. The noise is best described as a "pop" or "cough" and was not there before the cleaning and is also not there if I rev it smoothly rather than a quick blip, and is also not noticable when driving normally. Only heard when quickly blipping.

Does anyone have any thoughts? Is it possible the butterfly is sticking? Is there a lubricant that should be applied to the butterfly?

Suggestions please.

Thx

Edited by gofor28off
Link to comment
Share on other sites
  • 1 month later...
  • 2 months later...
thewraith Member

thewraith

Posted
Posted (edited)
I performed this service and now I have a "noise" when I quickly blip the throttle at idle. The noise is best described as a "pop" or "cough" and was not there before the cleaning and is also not there if I rev it smoothly rather than a quick blip, and is also not noticable when driving normally. Only heard when quickly blipping.

Does anyone have any thoughts? Is it possible the butterfly is sticking? Is there a lubricant that should be applied to the butterfly?

Suggestions please.

Thx

Maybe way too late but sounds like a loose or not entirely closing butterfly valve. I've seen people bend the valve too far back sometimes when cleaning it.

Edited by thewraith
Link to comment
Share on other sites
  • 2 months later...
gofor28off Member

gofor28off

Posted
Posted

The car is still making the sound and it is caused by the intake air being sucked through the TB faster than the butterfly is opening causing the "bark." This became significantly louder right after the cleaning.

I wonder if the cleaner I used is causing the butterfly to stick slightly causing slower movement, or it I pushed open too far or ???.

I am considering trying some lubricant; such as silicone spray or WD-40. Does anyone see any problem with spraying a lubricant in and around the contact points of the TB and butterfly? (I would remove it first).

One of my neighbors also has an '02 so I suppose I could try swapping the TB assemblies between the two cars and see if his makes the sound and mine doesn't after the swap. If that turns out to be the case I guess I will have to either live with it or buy a replacment TB.

Cheers

Link to comment
Share on other sites
  • 2 weeks later...
rustman Member

rustman

Posted
Posted

If anyone is thinking of cleaning your TB and you have an IPD plenum, be careful not to get any carb cleaner on the paint inside the plenum!!! While cleaning my TB today I sprayed the face of the butterfly with carb cleaner to loosen up the minor build. I cleaned the face of the BF and then the contact area of the TB "no problem". I opened the face of the BF to clean the backside of the BF and while doing so I notice the painted surface on the inside of the IPD intake plenum starting to wrinkle. Well you guessed it; now due to the fact that I have peeling paint on the inside of the intake plenum from the carb cleaner, I had to remove the plenum to clean off all of the flaky paint.

I hope I save someone some trouble.

Rustman

Link to comment
Share on other sites
  • 3 months later...
thewraith Member

thewraith

Posted
Posted
The car is still making the sound and it is caused by the intake air being sucked through the TB faster than the butterfly is opening causing the "bark." This became significantly louder right after the cleaning.

I wonder if the cleaner I used is causing the butterfly to stick slightly causing slower movement, or it I pushed open too far or ???.

I am considering trying some lubricant; such as silicone spray or WD-40. Does anyone see any problem with spraying a lubricant in and around the contact points of the TB and butterfly? (I would remove it first).

One of my neighbors also has an '02 so I suppose I could try swapping the TB assemblies between the two cars and see if his makes the sound and mine doesn't after the swap. If that turns out to be the case I guess I will have to either live with it or buy a replacment TB.

Cheers

I see no problems with this. I wouldn't even remove it- just stuff some paper towels in there before spraying.

Link to comment
Share on other sites
  • 1 month later...
  • 10 months later...
  • 11 months later...
b-man Member

b-man

Posted
Posted (edited)

If anyone is thinking of cleaning your TB and you have an IPD plenum, be careful not to get any carb cleaner on the paint inside the plenum!!! While cleaning my TB today I sprayed the face of the butterfly with carb cleaner to loosen up the minor build. I cleaned the face of the BF and then the contact area of the TB "no problem". I opened the face of the BF to clean the backside of the BF and while doing so I notice the painted surface on the inside of the IPD intake plenum starting to wrinkle. Well you guessed it; now due to the fact that I have peeling paint on the inside of the intake plenum from the carb cleaner, I had to remove the plenum to clean off all of the flaky paint.

I hope I save someone some trouble.

Rustman

I'm sorry to hear that Rustman. IPD should know better when they designed/made the throttle body . . .

b-man

Edited by b-man
Link to comment
Share on other sites
  • 7 months later...
DK570 Member

DK570

Posted
Posted

Hi,

stupid question maybe but here goes...

The butterfly appears still to be stiff to open on mine. Can it be opened by hand on a 2000 model C4 manual. I don't want to break anything??

thanks

If you are afraid of braking something, have someone else step on the pedal while you spray. This is the way the valve was designed to operate, so there is basically no chance of breakage. Pushing it with your finger I'm sure was not a designed operating condition.

Link to comment
Share on other sites
DK570 Member

DK570

Posted
Posted

If anyone is thinking of cleaning your TB and you have an IPD plenum, be careful not to get any carb cleaner on the paint inside the plenum!!! While cleaning my TB today I sprayed the face of the butterfly with carb cleaner to loosen up the minor build. I cleaned the face of the BF and then the contact area of the TB "no problem". I opened the face of the BF to clean the backside of the BF and while doing so I notice the painted surface on the inside of the IPD intake plenum starting to wrinkle. Well you guessed it; now due to the fact that I have peeling paint on the inside of the intake plenum from the carb cleaner, I had to remove the plenum to clean off all of the flaky paint.

I hope I save someone some trouble.

Rustman

Why would the inside of the plenum be painted? Every throttle body cleaner I've seen specifically says to avoid contact with painted surfaces. That would be hard to do if the interior of the plenum was painted!

Link to comment
Share on other sites
  • 1 year later...
1dmurrray Member

1dmurrray

Posted
Posted

I just cleaned the throttle body on my '01 C4 with CRC throttle body cleaner. I sprayed the cleaner on a microfiber rag, and wiped out all the dirt. The engine now purrs like a kitten, and idle, acceleration and deceleration are much smother. Great DIY. Thanks.

While I was at it, I put on a Schnell air intake kit. I prefer the throatier intake sound to the stock set up.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.