Jump to content
×
×

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

The following provides a description of some issues I have with my 1999 Porsche Carrara 4 (996, coupe, 6 speed) instrument cluster as a result of some “mishaps” while taking the cluster out of the car for backlight lamp replacement. I have also described the “mishaps” that I suspect have given rise to the issues I now face.

 

Problems with the cluster:

·     Voltage meter not working, shows slightly under 12v constantly, even with engine running

·     Speedometer dial not working, bounces around a little, but not correct

·     Tachometer stays at zero (previously climbed erratically to 8,000/max then stayed there, before I took it back out and moved the needle back to zero)

·     Temperature gauge not working, stays at minimum

·     The fuel gauge and oil pressure gauge are working normally

·     All digital readouts are working normally

·     The clock will not go into adjustment mode

·     The air bag warning light is on

 

Prior to the cluster removal, everything was working fine, except for 1 blown backlight bulb.

 

Now to the “mishaps”:

·      I disconnected the battery and removed the cluster with no issue

·     While the cluster was out and in the garage I inadvertently closed the front hood which I couldn’t re-open due to the hood release lever being locked (battery still disconnected)

·     In an attempt to charge the electrical system so I could open the hood I started the car using the battery terminals in the engine bay (remember, the cluster is out and battery disconnected). Not sure that was my wisest decision, where is the current from the alternator going?!?!

·     Eventually I got the hood back open via manually operating the cable (long story!)

·      I reconnected the battery to avoid the issue again

·     After replacing bulbs in the instrument cluster, I forgot to disconnect the battery again before re-fitting the instrument cluster

 

I have since disconnected & re-connected the battery. I have tried to check for codes with an OBDII tester. I have removed the cluster again, stripped it down again and carefully re-fitted ensuring all connectors / harnesses are fully pushed into place. I have even pulled every single fuse one by one to perform a visual inspection (all were OK).

 

I suspect I may have damaged the cluster by re-fitting the cluster while the battery was connected, but can’t be sure.

 

Any advice from anyone as to what to do next to diagnose the issue and where to go with this saga now?

 

Many thanks in advance.

Share this post


Link to post
Share on other sites
    You can remove these ads by becoming a Contributing Member.

Thanks Loren. I'll try and find a local repair facility with one of these diagnostics tools. I'll update with the outcome.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.