Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Troubleshooting my 986's Random Shutdowns


Recommended Posts

At the end of last year, I drove the car from ID to NC with two quick stalls/misfires going over a mountain in Montana. The rest of the trip, it was perfect. I had serviced it before leaving my parents' home there, as it had spent a good bit of time in storage. Now, when I'm on the road, it will occasionally completely shut down the engine. I roll to the side of the road, then can get it started after four or five tries (it always cranks). Engine temp really makes no difference. Occasionally, I can kill it immediately if I engage the a/c compressor at idle.

 

What I've replaced so far:

 

  • Idle Air Control Valve
  • MAF
  • Fuel Pump
  • Fuel Pump Relay
  • Coil/O2/injection relay (rear panel)
  • DME relay (rear panel)
  • Battery (my stepdad had the wrong one in there)
  • Accessory drive/serpentine belt
  • Air filter
  • Crank position sensor

 

I did locate an old mouse nesting spot between the rear trunk carpet and the firewall (near where the coolant hoses go through). That's all been cleaned up and I couldn't spot any chewed wiring, etc.

Interesting development with this car today. I went to start it up to point it the other way in the garage. When I went to position 1 with the key (where I always pause to glance at the oil level), a rapping noise started coming from the area of the right rear wheel well..."rat-a-tat-tat-tat-tat-tat". Like muffled automatic rifle fire. As it was happening, the cluster lights were flickering. I shut it off, then tried again.

 

It didn't happen again, but it did take ten or so attempts to start the car (it did crank every time). Once I got it going, textbook idle with no problems. I engaged the a/c compressor, idle adjusted as designed. I've made room for ignition switch replacement gymnastics (for this 6' 3" guy) tomorrow, and will hook up the laptop (Durametric) as well.

In the meantime, any thoughts or ideas are more than welcome. Thanks, all.

Edited by BobieMac
Link to comment
Share on other sites

I had an Audi that developed random stalls. Ran perfectly, and just before the warranty ran out the dealer said there was an interior oil leak in the engine ??? They replaced the heads and bingo, random stalls. I traded the car before the warranty ran out. A few weeks later I spoke with the tech (in the parts dept) that worked on my car for most of the last two years, something the dealer wouldn't let me do - speak to the tech, and he said the new sensors they installed had a different size vacuum fitting and the vacuum hoses no longer fit well enough so they would used clamps to make them fit tight.

 

Long way of saying check the vacuum.

Edited by ttocs
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.