Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Pablo C

Members
  • Posts

    3
  • Joined

  • Last visited

Everything posted by Pablo C

  1. I've seen the clip before and yes that's sound like the ticking I'm getting, no need to upload lol. A endoscope is in my future. incidentally I was able to use a "mechanics ear" and listen to all the belt driven items, unfortunately/fortunately they all check out fine with regards to any funky noises. The slightly higher revs, like you surmised must be drowning out the ticking. I would of thought the opposite, that the ticking would get louder as rpm's increased? Once scored, do they continue to get worse or can it be managed? I do not have any abnormal smoke or soot inside either tailpipe, no oil level fluctuations and all looks clean so far, although its was changed just 200 miles ago. Looks like I'm in a heighten monitor mode. Other than a bore scope, or there any other items I should be checking or monitoring? Thank you both for helping out, it is much appreciated.
  2. Yes, started to do that, via the old fashion way with a long screw driver, since ordered up a mechanics stethoscope, should be here by the weekend. Incidentally, I can get better access if I remove the air box, but in doing that, the AC will not function, I'm assuming that has to do with the MAF being disconnected? Is there anything else I should be looking at? Many questions, but I'll hold off for now until i have more data to report. Thanks Paul
  3. Hi All, new member here and most happy to join the community! Ive been able to find much information and the DIY's are spot on, so thank you all. Can use some help, first the particulars, I'm from Northern California and I have had my 1999 911 996 C2 Cab for ten years, 6 speed manual, 50,000 miles. I was told the IMS bearing had been done. Recently, I have changed the oil and filter (mobil 1 0w-40), filter clean. Air and cabin filters, fuel filter, plugs (not coils) water pump, low temp thermostat, upper idler pulley and serpentine belt. Now the problem, the engine idle ticking, after 2-5 mins after start, (I believe its just at idle) has been going on for a few thousand miles or more, all my searches point me to piston slap, bore scoring, sticky lifters....etc. However, while trying to listen for the source, I read somewhere to turn on the AC and bingo the noise went away, or it was drowned out by Ac compressor, but I don't think so, turn it off, noise back comes back. I was going try to run it without the belt to try and rule out some of the accessory items, but the noise doesn't start for a couple of minutes and that's to long wait before I cause major problemos. What should be my next trouble shooting steps, or am I'm just grasping at straws in hoping for a simpler fix other then bore scoping and the like. Thank you Paul
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.