Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

otto

Members
  • Posts

    6
  • Joined

  • Last visited

Everything posted by otto

  1. OK, I bypassed the clutch micro-switch and the beast starts immediately without any delay. I have ordered the part and hopefully problem solved
  2. Thanks Maurice, The fuse in the immobilizer is fine. It was a pain in the ... to get the seat out but all went well. No moisture in or around the immobilizer. I'll try bypassing the clutch switch tomorrow.
  3. Now I'm not sure that zip tying the micro switch is correct. The way the switch works if I zip tie it will be the same as if the clutch is not depressed. The plunger on the switch moves outward when the clutch is depressed and goes all the way out before the clutch pedal hits the bottom. No I'm not certain the recently replaced electrical portion of the ignition switch is the issue. All I know is that it acts the same as before it was replaced. I assume the battery ground is good. No other issues with car electrical systems. Not sure about the starter other than the fact that it always starts. It's just a delay issue like sometype of communication error. I'm going to take out the seat and check the fuse on the immobilizer.
  4. To White987S, I'm not very bright when it comes to electrical stuff. OK, I know how to zip tie the clutch micro Switch and I assume that in order to bypass the switch I would just disconnect the two wires to the switch and runner a jumper between them. Is this correct??
  5. It just sits there. All lights come on same as turning key to Aux position but when turn further to start engine there is a delay which sometimes is only a second or two. No flashing lights. Sometimes the delay is 10 seconds or more and if it doesn't start at this point I start over. Remove the key, put the key back in ignition, check emergency brake on, depress clutch all the way then turn key again. As it goes through aux position all warning lights come on and continue turning key to start position then it might start immediately or it delay's again and might start after a few seconds or maybe not and then repeat again after 10-15 seconds. Sometimes I go through this procedure 4-5 times before it starts but it always eventually starts. Everything else works fine in the car. It's just this inconsistant delay. Also, I purchased this car second hand and it only came with one key so I don't have a second one to try.
  6. I am experiencing a starter delay with my 2003 Boxster S 6 speed. Key turns normally from O through start. Emergency brake is on, clutch is depressed, and shifter is in neutral. Battery is new. All my idiot lights come on. Sometimes it will start immediately as normal. Other times have to turn key to off position then try again. Sometimes have to hold switch in start postion 10-15 seconds. Car will always start but sometimes takes as many as 5 trys. I have replaced the electical portion of the ignition switch and continue to have the same problem. Any ideas
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.