Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Search the Community
Showing results for tags 'drl'.
Found 2 results
Gnochi posted a topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)Hi all, I'm in the midst of designing a DRL setup for my 996.2 (which is a topic I recognize has been done to death). That said, I'm not a fan of LED light bars, and while I don't mind halos, this is a Porsche, not a BMW. Therefore, I'm taking inspiration from the Four Point Principle. I'm using 8x total Luxeon Star 10mm square LED blocks, neutral white, with 10mm square Carclo 10415 elliptical-pattern lenses, and a 350mA FlexBlock on each side. DRLs should be on the order of 400 lumen per side and 1500Cd at the center, so I'll be using slightly lower currents than the LEDs are made for. As soon as I get dimensions 1,2,3 in the attached image, or even better a damaged 996.2 headlight unit, I'll figure out heat sinking, but it will be relatively unimportant at 4W per side, 150C maximum junction temperature, and 100F approximate steady state temperature insight the HID housing (per Pedro's Garage). As far as wiring goes, here are my requirements: DRLs turn on with the engine DRLs turn off with the low beams The low beams can be turned on whether the engine is on or not. There are several ways to do this, of course, and I think I've picked the easiest: 1x Bosch relay with both NC and NO pins, connecting to 1x 928-610-511-00 relay carrier added to an open spot in the relay block Pin 30 connects to a fuse tap at A6 - Seat heater (switched on with ignition) Pin 85 connects to any conveniently-located bolt to chassis, possibly in the fuse box. TBD. Pin 86 connects to a fuse tap at A9 - Low Beam Right (switched on with headlights) Pin 87a is wired to the left and right FlexBlocks in parallel. Pin 87 is not necessary The relays I have take about 150mA to switch, which *shouldn't* noticeably affect the low beams, but does put additional stress on the headlight switch. If that causes problems I might need to do the following instead: 2x Bosch relays with NC/NO pins Pin 30-1 connects to A6 Pin 30-2 connects to D5 - Cigar lighter (always on) 85-1 splices into 85-2, connected to chassis ground 86-1 splices into 86-2, interrupting the YE/WH wire running from the light selector stalk before it splits to go to A9/A10/Canada DRL block 87A-1 is wired to left and right FlexBlocks as above 87-2 is wired to the other side of the YE/WH split Thoughts? Anyone have input on headlight switch reliability or wiring plans?
I'm wondering if anybody knows of a way of disabling the all lights off switch position in a 997.1 - the position to the left of "Home" on the light switch control. I've done a DRL hack to get my fog lights to come on when the engine starts if the switch is in the "Home" position, but also need them to remain/come on even in the "All off" position. The regulations for DRLs in Canada specifically call out no manual way to turn off the DRLs via a switch when the car is on. Any thoughts?