Jump to content

The RennTech.org community is Member supported!  Please consider an ANNUAL donation to help keep this site operating.
Click here to Donate

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

I am referring to the pair of cables that hold down the back part of the soft top while in the up position. These have sockets on each end that pop onto ball joints.

There is an article saying that if these cables aren't tensioned properly, a "loose change" sound can be heard from behind the drivers shoulder.

Is the "loose change" sound caused by this heard with the top up, down, or both? Just how tight should one set the tension? With the top up, I can fold the seat backs forward, reach through the roll hoops, and feel the tension in these cables. I currently have about 1/8" slack or play in the cables. Am I supposed to turn the adjustment screws (clockwise?) until all of the play is gone?

My problem is that I hear the loose change sound with the top in the up or down position. It kind of feels like it is coming from inside the driver's door, but I really don't want to be reinventing the wheel here. If the cables are supposed to be tight, I will try that first.

Thanks

PS, if this turns out not to be related to any adjustments, what are all the lubrications points?

Link to post
Share on other sites
    You can remove these ads by becoming a Contributing Member.

  • 2 months later...

I'm curious to know what this bolt actually adjusts. I hear a (the) noise somewhere around my left shoulder (American-left hand drive). I hear the noise when I hit certain kinds of bumps. Often it sounds like it is in the door - maybe the plastic latch cable-housing rattling between the door and the interior panel?

I tighted the bolt indicated in the picture about 3/4 to one turn. It felt snug (the whole time I turned it), but that could be drag caused by friction in the threads. Maybe I didn't tighten it enough, but the sound is still there. If I know what was tightening exactly, or some way to tell if I've over-tightened it, I think I would have a better idea of what to do. If I tighten it too much (not so much to shear the head off) will something break? Will the top open or close differently? Should I be tightening each side equally? (I have so far.)

Link to post
Share on other sites
I hear a (the) noise somewhere around my left shoulder (American-left hand drive). I hear the noise when I hit certain kinds of bumps. Often it sounds like it is in the door - maybe the plastic latch cable-housing rattling between the door and the interior panel?

Badcow-

I also had a very annoying clicking / ticking / loose change noise when the top was up or down. It sounded like it was coming from about ear level. I finally found there was a piece of clear tape missing on a small cable guide. I covered the guide up with a piece of 3/4 x 1 inch of clear packing tape and the noise went away for good! Here's how to check yours:

Open the top almost fully so that there is about 12" between the edge of the top and body of the car. Look into the cavity where the top goes, about 6 inches from the end of the door. You will see a red cap on part of the top mechanism. Now look a few inches further to the rear and you will see a cable that terminates on a connector with a star washer and torex screw. Note that the cable is bare for about an inch and then is covered with a black insulator. Right where the bare cable ends you will see a 1" wide thin metal plate that acts as a guide/clamp for the cable. Check to see if there is a piece of clear plastic tape on this. If not, just cover it with a piece of tape and you're in business. It solved my problem and while you're at it, I'd check the other side too.

Another problem could be change stuck in your center console. Ever put any in the ash tray? If so, pop the cover off your shifter and look around in there - especially right on the sides as there are metal plates there. I bought my Boxster used and got $1.83 rebate on it after I fished all the loose change out of the console. You'd be surprised to find out where the sound appears to come from and where it really is coming from. The change sound I could have sworn was coming from the dash on the passenger side...

Hope this helps and feel free to pm me if not and I'll take a pics.

Link to post
Share on other sites
Hillarious, I thought I was the only one. I got a $23.00 rebate that I found when I was replacing my Prake Brake Switch. :beer:

We have $1 & $2 coins in Canada.

That telescopic magnet paid for itself that day!

So basically the same rebate... $23 CND = $1.83 US right? Just kidding.

Link to post
Share on other sites

Badcow-

Per the PM, here are pictures from driver's side of vehichle w/ top opened all but about 12". The torx screw, cable and metal piece are almost dead even w/ the slide tab for the clamshell.

post-9673-1163772211_thumb.jpg

Close up of red circle. You can see the clear packing tape I put on LY is starting to show signs of where. At least next time, I'll know right away where to look and replace. Your existing piece of clear tape is probably just flapping away right there.

post-9673-1163772312_thumb.jpg

Take a look and let me know if this solves your problem

Link to post
Share on other sites

OK. No luck here. After fixing the tape on one side (as indicated in the pictures) we went on a short drive around town, top down, still had the noise.

Since it was a cool day, we had the windows up. I mentioned the noise to my S.O. and she said she heard it on her side, too. Just for kicks, I held the window tight against the windshield pillar. The noise stopped. S.O. did the same thing on her side. The noise stopped there, too.

So. What does this mean? Is there something loose in the door or is this just the glass rattleing in the guides?

Hmmmm...

Link to post
Share on other sites

Badcow-

Not sure if you've solved your problem yet or not, but apparently there is an adjustement you can make to the in/out of the window w/in the frame. I just picked this up on another board and thought it might help you.

"Underneath the door, there is a plug. Remove it and there is a set-screw in there that loosens the window in-out. You only get a few centimeters of play. "

I think I saw something here similar but was posted as part of a message regarding a window regulator.

http://www.renntech.org/forums/index.php?s...l=rivet++window

Scroll about 1/4 down for a post from Mitty on 8/31/04. Thought this might help.

Link to post
Share on other sites
  • 8 years later...

Do the tension cables serve any purpose when the top is open and folded?  I ask because when open I seem to have slack in the exposed portion of the cloth top once the clam shell is closed tight.  In the past, the exposed portion of the cloth top, when open, has been nice and taught.....not not so.

 

Any thoughts????

Edited by Rob175
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.