Jump to content

The RennTech.org community is Member supported!  Please consider an ANNUAL donation to help keep this site operating.
Click here to Donate

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

This is a side project so we only work on it every so often. but yes, we have durametrics but havent hooked it up yet and yes the engine spins over fine when the pins are jumped but will not start. I will report back once we check some more things.

Link to post
Share on other sites
    You can remove these ads by becoming a Contributing Member.

ok, everything seems to be there except the ground from the ECU when in the crank/start position. If I ground the wire at the relay, the starter will turn over with the key but it still wont start. EVerything leads to a bad immobilizer except for the fact that it is brand new and been coded and tested.

Does anyone know of a place i can send the ECU to get it reprogrammed so it doesnt need the immobilizer? I would think most race cars have had this done??

Link to post
Share on other sites

A few things I can think of:

- the 15A fuse on the alarm module itself

- are all the airbags intact and car has not been in a crash. Alarm takes input signal from the crash unit

- key RFID signal coil and transformer which feeds to the alarm

Link to post
Share on other sites

fixed... lesson learned. it was an immobilizer problem. sort of.. For all to see--- as i mentioned earlier, we did not have a key, just the remote head. We had it taped (or held) up to the module on top of the ignition switch which picks up the chip in the key but apparently it has to be exactly right inside the ignition sensor ring and not just @ 1/2" away on top of it. We simply held the key fob in the exact place it would be if we had a key and it fired right up on the first crank.. That's a little embarrassing but I cant believe simply moving it 1/2" solved this problem. Doi !!

Edited by rattlsnak
Link to post
Share on other sites

What is involved in changing the DME in a 1999 C4 6-speed? I have a replacement unit with the same part number, Durametric reports no fault codes but the car will not start because the replacement DME is not coded to the car. What info do I need to have the replacement DME coded to my car? Do I need any info from the donor vehicle? (VIN?) Thanks Paul G

The DME failed on my 2000 C2. After diagnosis, it did not take the dealer long to complete the swap. New DME was loaded with info from old DME, and they reminded me to bring my spare keys so that the new Imobilizer could be programmed to accept them.

As an aside, this was done well past warranty by a dealer who did not sell me the car. Hennessy in north Atlanta said they found this to be so rare that they would give me the part at cost and charge no labor for the job. That's my kind of dealer.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.