Jump to content

The RennTech.org community is Member supported!  Please consider an ANNUAL donation to help keep this site operating.
Click here to Donate

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Strange (non)starting behaviour, 996 GT3 mk1


Recommended Posts

I have noticed a strange behaviour of my car lately :( Occationally the car starts on the first attempt, but usually not. It does not seem to be low battery state of charge as all the control lamps in the instrument cluster is lit up and the compartment fan is blowing. When the engine has started the voltage level seems to be normal. It does not matter if I have been driving for 300 km or more or just a short run. The car has covered some 40000 km and is of model year 2000, Club Sport package.

When I turn the ignition key all the lamps in the cluster is lit up and I switch to the “start” position. Then I hear a noise from the engine as if it would start but without turning the engine the “start” procedure is interrupted. No cranking of the engine or anything, so it does not seem to be the fuel system. Then I wait a few seconds and turn the ignition key to “start” again and sometimes the engine starts at the second attempt and sometimes at the third/fourth/... attempt. So far the engine has always started, but I’m fearing the day when it will not and I am far away from home.

Could it be the starter(motor), the cog-wheel(?) that is supposed to turn the fly wheel to start the engine?

I have never replaced the battery of the key, could it be low state of charge of the battery in the key (immobiliser does not get the code to “release” the start procedure)? But that does not explain the random start behaviour?

Is it the nearest Porsche Center next?

Any suggestions would be appreciated.

Regards

Anders Johansson

Sweden

Link to post
Share on other sites
    You can remove these ads by becoming a Contributing Member.

  • 2 months later...

It is your starter motor. I had thios at about 35k miles. There is some sort of centrifgal clutch element in the starter motor, which is supposed to disengage drive when the engine starts. The clutch pack is worn, so it disengages at a much lower torque than is needed to crank over the engine.

Option 1: go to Porsche and get starter motor replaced.

Cheaper (DIY) option - remove starter motor yourself (it is a bit tricky, will take about 1 hr) and send to any competent auto electrician for repair. It cost me £50 to get mine reconditioned. You don't need to lower engine or gearbox to remove the starter - it can be done in situ - its just a bit tricky.

The replacement is quite tricky, as getting the bolts in is a PITA - but it can be done.

Link to post
Share on other sites

John is probably right. Although a mate had similar problems and it was just the relay - worth a try, but I was not so lucky.

You need a range of socket set extensions and a knuckle joint to access the bolts - pita to torque up.

Cheapest I could find was a recon unit from ALTERNATOR MART.CO.UK 994 Astley Street Dukinfield Cheshire

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.