Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)
Sign in to follow this  
valcax

Pneumatic Springs

Recommended Posts

Hello!

I need part number

Pneumatic Spring (2) of Rear Lid

Boxster 2.5 MY99

thanks!!

Share this post


Link to post
Share on other sites
    You can remove these ads by becoming a Contributing Member.

HELLO!

I am looking for a DIY to replace pneumatic spings.. I cannot find..... can you help me?

thanks

Share this post


Link to post
Share on other sites

HELLO!

I am looking for a DIY to replace pneumatic spings.. I cannot find..... can you help me?

thanks

Valcax:

Assuming you are talking about the trunk lid supports and that they are the same as in '97 Boxster, here is a DIY I had written up a few years ago:

Looking at the ends of the hydraulic arms from their backside (i.e., not the side that presses on to the metal balls), you will see a thin, black curved spring steel strap that wraps around the rounded, curved part of the arm end (one on each side of each hydraulic cylinder). You will also notice that there is a groove that starts at the outboard end of each of the spring steel straps and goes on a diagonal away from the steel strap.

Insert a small, THIN flat bladed screw driver under the center of the spring steel strap STARTING FROM THE SIDE CLOSEST TO THE CENTER OF THE HYDRAULIC ARM (We will call that the inboard side). Then, while pressing in, lever the black spring steel strap upwards so that it sort of rotates around and ends up being guided into the diagonal slots. Be careful that the small steel strap doesn't get airborne because it is spring steel and it can pop out with some force.

Continue to pry off the steel strap and once it's out, the hydraulic arm will easily pull away from steel ball.

Installation is the opposite. Press in the steel strap while rotating it around inboard into position so that it ends up flat across the back of each rounded, curved part on the end of each arm.

Check to make sure that each spring strap is firmly seated and try to separate the ball from its socket by pulling it apart. It should not pull apart if the straps are seated properly.

Regards, Maurice.

  • Upvote 1

Share this post


Link to post
Share on other sites

thanks Maurice,

url of this DIY? I remenber there were pics

Valcax:

When I wrote it up, it was without pics. I think I first posted it on PPBB.com about three years ago.

If you follow the words carefully, you will be able to get them off and on. It will make more sense once you look closely at the ends of the struts and the little metal strap that locks them on.

Regards, Maurice.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.