Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
I'm new to the Porsche family.... Just over a month and the proud owner of a 1999 Boxster. It's a project car but still on the road and my point to point ride. Must say, LOVE to drive this car....This one has been lowered some, well alot... and does it hug the road..... Just doesn't miss much being that low.... My question is, I am having an issue with the rear lights on this car... I know I had a problem with the left rear brake light. I tried tracing back the wire but found no problem... I then switched the lamp holder from the right side to the left and all the lights worked... So I thought I had an equipment issue. I bought a (Porsche) replacement bulb holder. Came in last night. Changed out today...Guess what???? Turn indicators work, Backup lights work, Brake light works on the Right Side ONLY, (still) Now no rear tail lights what so ever......I have checked ALL the fuses, only had to replace one and it had nothing to do with the lights. NOTHING has changed....Where did my tail lights go?????? Can't figure this out.......Please help.......Just FYI, ALL the LIGHTS were working as of last Wed. when I did the bulb holder swap and checking the lights. Power is to both wire harnesses. Everything else works except the left brake light and the drive lights. Go figure.......
I'm new to this website. Here is a question:
I have a 1998 Boxster 2.5 Tiptronic. I just had a new key programmed at dealership ( the old key fob newer worked). With new key fob, all doors (including gas) lock and unlock appropriately. However, when pressing the button to open the rear trunk lid, the lid doesn't move and the rear lock actuator/solenoid is silent. I disconnected the actuator from the car (separating the plastic connector) and using a 9v battery, made the actuator ( and lock) open and close. So I believe the problem is not the actuator. I also connected a volt meter to the two wires that connect from the car to the actuator, then pressed the fob button, and no voltage was recorded. However, the red light on the fob and the red light on the dash near the windshield did light up
So i believe the problem lies in the electrical system somewhere between the actuator and the fob. Any ideas on how to test the wiring running from the trunk lock actuator to the CLU? immobilizer? or wherever it goes? Or should I be spending my time evaluating the CLU? immobilizer? ??
Thanks for any advise!
By Tim Lambie (Trailbrake)
Several people have told me that the 996 Dual Sender Oil Pressure Switch/Sensor will directly replace the 987-1 Oil Pressure Switch. Can you please confirm this and provide the part number. I would guess it is 996-606-203-03 but, I would like to be sure.
Additionally, if I am running an AIM dash, should I run the pressure lead to the switch input on the ECU and get the pressure data from the CAN bus or, just leave the switch lead attached and run the pressure lead straight to an analog I/O on the AIM dash.
I am missing the shift knob insert to my Boxster S 6 speed and cannot find a replacement anywhere without having to buy a whole new shifter... Does anyone
have one they would like to donate or sale? Or does anyone have any ideas on how to get one. Its just the insert that fits on top of the shifter Reverse through 6th...
Or does anyone have any ideas on how to make one? I am at a loss and it looks raty without the insert.....
Thanks in Advance!
Hey everyone, i own a 2010 porsche Boxter 2.9L with the PDK transmission.. yesterday after leaving the car for a 4 days i started it and went for a drive.. when i turned it on again, i got a warning message “emergency transmission run” and the car became very jerky through gearshifts and wouldnt accelerate properly.. after turning it on and off the message went away and it drove just fine but then it kept re-appearing mid drives and becomes very jerky and clunky...ive noticed since i had the car that the gearbox was sometimes clunky or would make a noise when changing gear but the dealership said that was fine and normal since its a PDK, the car is at 59,000km so its time for a transmission fluid change... could this be a low voltage problem, or transmission fluid? The reverse gear works just fine.. has this happened to any other owners?