Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
By Kevin Bryck
Okay this is REALLY specific.
The adjustable tension cable on the drivers side of my cabriolet disconnected at the top where it threads (8mm) into the top frame, not at the bottom where it snaps onto the ball.
The is a larger diameter (10mm?) clean smooth painted hole where the cable needs to thread in, which leads to the presumption that there was a nut on the back side?
Searched all over including removing driver's side rear 'door' panel and fishing around with a magnet but no loose nut found.
Looks like getting to back side of this frame casting would entail a major disassembly of the cabriolet top frame?
Also, what does this clip that goes over hydraulic cylinder do?
Right side clips is in place about halfway down length of cylinder.
Left side clip was down around the base of the shaft.
Replacing it where there appears to be a shiny spot looks like it would interfere with the cabriolet top potentiometer arm.
Right cable threaded into frame at top
Right cable threaded into frame at top
Missing cable location
Smooth clean painted hole in top frame where 8mm cable end is supposed to thread in
Left upper cable end with 8mm thread
I just bought myself my first Porsche, a 1998 Boxster. I have an issue with the soft top that I'd like to get some guidance on.
The top goes down smoothly with no issues. It also comes up smoothly until it is nearly all the way up. Just before the dashboard Top light goes out, there is a pretty sharp metallic twang or snap. It did this when I was looking at the car before purchase, and it did it again this evening when I put the top up after driving the car home. I'm assuming it's getting caught on something but I wonder if anyone might have suggestions on what to look at given the late point in the cycle where it occurs?
The convertible top on my '99 Boxster has been acting up for the past few years. Sometimes worked fine and other times wouldn't work at all. I had it looked at by my local shop and by my local Porsche service center. My local shop replaced the switch in the convertible top latch housing (a few years ago) and then the emergency break switch (a couple years ago). This didn't solve the problem. Then a couple of weeks ago the Porsche service center again replaced the emergency break switch, again not solving the problem. Over the past week or so the top had completely stopped working, but then this morning it was working again (intermittently). The tech at Porsche said that everything has been checked (relay, switches, etc.) so he suggests replacing the convertible top motor for approximately $2500. I'd appreciate insights from anyone that has been through this. I see quite a few posts re malfunctioning tops so any info will be helpful.
I purchased a 1999 Porsche Boxster 986 about a year ago and I'm having a few problems with the electrical accessories. The top worked fine when I bought it, but now it won't work sometimes. The radio also turns on, then immediately off at startup, and it won' turn back on until a few minutes later either by itself, when I use turn signals, power windows, brake, or even just by itself. After the car is "warmed up", then it will stay on. Other things won't work right or not at all, such as the alarms for, ignition, door open, light switches, etc. The fuses are all fine, and I know the battery had been replaced right before I purchased it. I haven't checked the relay for the top, but I am about to do that now. I feel like there could be a single problem creating all these issues. Any help would be greatly helpful and appreciated!
So I noticed one of the velcro straps in my top broke from the top and is hanging from the metal bar, so I just took it off. Is this strap supposed to help guide the top under the plastic channel when closed or something else, because as you can see in the 2nd pic on the right, the top still closes correctly and tucks nicely under the channel even with the strap off. Just curious what that strap is for and if I really need to sew it back in place. Thanks.