Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
By Paul Forster
Just picked up an 01 996 Carrara and PO had installed a battery tender on the passenger side beside the battery tray but it was no longer functional, so I removed it. In the same area to the passenger side of the battery compartment there is a flexible clear tube unattached at its distal end originating close to the fuel filler neck.
Any idea what the tube is and is it correct for it to be disconnected
By Charles Bradley
My drivers' side headlight was replaced by the dealership after an accident. It has worked fine for two years since, but recently decided to stop working. I get a "check dipped beam" message on the cluster as a result. The turn signals work, as does a single little light on the outer side of the assembly. The main and high beam do not.
After taking it out to inspect, I noticed that the electrical harness connector on the back was the problem. When I could force it into the headlights socket, the lights all powered up and worked fine, as did the high beam. So a poor connection is the culprit.
One of the tabs on the side of the white connector was broken off, so the connector wiggles in its place. I imagine that the force of the headlight being pushed back wiggled it just enough that it wouldnt' seat into the headlight assembly. But getting that white connector into the socket and then back into its place without being able to get my hand in from the rear of the light was not apparent. I also noted that the insulation on all the wires was terribly frayed and coming off in my hands as I examined it.
But with a new connector in hand, I don't see how to wiggle the old one out. It slides in from the side on the back of the tray holding the headlight assembly, but is blocked from sliding out all the way.
How do I rectify this?
I have a 2004 Cayenne S. I just got it recently, interior lights have never worked. I checked the fuse and it was blown. It calls for a 20 amp fuse but the blown one in it was a 25 amp. I had the key in the ignition if I remember correctly and put the new 20 amp fuse in and everything came on. Side note, I noticed a weird glitch with the light above the rear passenger side door and the switch on the main map reading light. The interior lights had gone off and I turned the back on and the backlight above to passenger side door was very dim. I slid the switch on the overhead console for the main map light and the rear light came back to full strength. I found that odd. Everything then worked fine. I took the key out. Next time I put the key in, immediately heard the fuse blow. Any ideas on where to start?
When battery is dead the electrical system is down, as is the trunk for accessing battery.
I have tried connecting positive to red fuse and negative to door arm. I ran current using jump starter but could not get latch to open. Does anyone have any other ideas to open truck, e.g. force lift? Thanks in advance.
Is this also true for current year C4S?
Quote for 1999 911: <<There should be a release cable under one of the headlights. You need to use something to fish it out. If you do a search at renntech.org you will find it.>>
By Jared Imapirate
I am currently trying to repair my 2001 Boxster 2.7 as the coolant temperature gauge no longer reads and the coolant light is flashing at about 1 hz. The coolant temperature sensor pigtail had broken wires too close to the connector itself to effectively solder back together. I searched for several days and couldnt find anyone selling a specifically designated coolant temperature sensor pigtail, but the engine knock sensor pigtail seemed to fit. I installed that part and reconnected the wires with a good soldered connection and plugged everything in, unplugged the battery for about 10 minutes to reset the code, restarted the engine and was greeted with the same flashing light. The coolant temp sensor itself has been replaced, the coolant level is solid and the engine has been burped. Several times. Any thoughts?