Welcome to RennTech.org Community, Guest
I got my 2014 Cayenne Platinum edition and it seems that the remote unlock and locking mechanism using my key fob does not work unless i am close to the vehicle, range is i would say 5 feet.
I tried to change the batteries on the key fob but issue still there, is there anything else i am missing or is it a design issue by Porsche that they corrected on a later versions ?
I have one key fob that works and one key fob that doesn’t. At least one does. No transmit light on the other with a new battery. Switches feel like they are working. Is there a reset procedure?
Neither key will work manually in the drivers door lock. Is the door lock electronic or should I feel a mechanical linkage movement?
Nervous with only one key fob that’s the only way to unlock the car.
The rear window on my 2001 S has separated from the canvas, and the tan top is dingy and past its prime. I no longer have a garage, so I am forced to outsource it. I would appreciate some informed opinions.
I'm looking at a GAAH A5 Acoustic glass window top. The dealer is saying $2,700-$3k installed. A reputable convertible/interior specialist is coming in at $2,200. The dealer talked about needing to buy additional sound insulation, clips and etc., which is either building in additional profit, or it may be totally justified because they have experience and might provide additional quality. I don't have an excess of cash for a 18 y/o car so I'm soliciting experienced opinions:
Assuming the local top specialist is truly skilled at their game, should I expect that they can handle this, along with connecting the heating element? I doubt they have done many A5 Acoustic glass retrofits, whereas the dealer has likely done a few. If I go with the local specialists, are there some unique things I need to specify they order/replace/pay attention to? Should I give more weight to (a) Porsche dealer that only occasionally does a top or (b) the people who do tops all the time, but just not Porsches?
All informed opinions are welcome.
Have an 05 987 and I’m trying to replace the old broken fob clamshell with I new heavier one. Got it all figured out, but I’m having trouble extracting the transponder from the old fob. Don’t want to break it trying to get it out. Is it glued in? Suggestions welcomed!
My first post here so please bear with me but pretty desperate for help. Have 2004 Boxster S and its, in general, running a bit rough (feels fuel rich). It also will also, on occasion, not go. Pulling up at a busy intersection and car reduces to Idle. Then put the foot down and the car stays at idle. Normally an engine restart gets things going again (although not always and sometimes requires a few goes).
Bought a computer reader and found error codes
P0102: Factory Fault code 115 - Mass air flow sensor - below limit
P2135: Accelerator Pedal - Signal Implausible
P0121: Factor Fault code 117 - Throttle value or accelerator pedal potentiometer - signal implausible
P1266: Factory Fault Code 409 - Fuel shutoff function monitor - signal implausible
Took the car to Porsche. They suggest a MAF sensor was the root cause and replaced it. It felt better for a few days then problem returned. They replaced another MAF sensor.. Same problem. They then said the MAF reads 0 and have checked the cables so its me DME and it needs replacing (not cheap)
Have taken the car back home and looked at the likely affecting values myself from the computer.
The computer shows to different values for MAF
Mass air flow (HFM) is always 0 regardless of if the car is working correctly or not and at any accelerator level
Mass air flow seems to move within a range of 18 (idle) to 100 (full throttle)
2. Throttle (since it had error codes on this)
Pedal encoder potentiometer 1 and 2 always move and the pedal value goes from 0-100% when its working but stays at 0 when its not. Since the potentiometers always move I am assuming the DME simply can't add things up so sticks the pedal value at 0.
ie. The MAF sensor reading above confuses the DME and it reduces the throttle to 0. That feel consistent with the behaviour of the car (its just sticks at idle)
Any one with any clues? Certainly don't want to replace the DME unless absolutely necessary....