Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)
  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Garra671
      Recently I had been noticing issues with my cooling system the coolant temp guage would go past the 0 on 180 and I wouldn’t hear fans or anything. (Already tested fans and resistors and relays).   The temperature Will continue to creep up if I sit still, with no signs of fans, AC OFF.

      I replaced the coolant temp sensor. Problem fixed!! Then same issue again it seems after a week of driving.  

      Now i currently have ordered another temp sensor just Incase I maybe did something to cause the other new one too fail, I’ll be changing it again today.

      However I was doing the climate control hack to check my actual temperatures today while doing a short troubleshooting drive. And I noticed my oil temperature said 0, which is physically impossible 🙄


      Is it possible the oil temp guage is throwing off the coolant sensor?    Is it even possible for the oil temp sensor too go bad but not the oil level sensor? (They are a 2 in 1 sensor)   

      THANK YOU IN ADVANCE
    • By Bardia Manafi
      Hi all, just purchased a 1961 notchback 1600s, I have never drove a Porsche until the day I purchased this car, got the bug now and i love Porsches more than ever now, the car is in very good shape, but i want to change all the fluids, grease all the parts, and do all the maintenance there is, the oil was so dark when I checked the level and it was all the way to max line of the stick, i would appreciate if you guys can tell me where to buy all the maintenance parts, and where can I buy the shop manual, and what are the things I should do, there is a small leak on the floor from engine very small, but a palm size of oil from transmission on the ground,  thanks guys cheers😁

    • By Tonel
      2002
      911 C4S
      Six speed manual
       
      When driving my recent purchase, the oil pressure gauge reads "5" whenever the tach goes 2500 rpm or above in any gear. This is when it is still warming up or at operating temperature (180), after at least 30 minutes on the road. Needless to say, I've been keeping the car below 2500 as much as I can. At idle, it registers between 2-3 after reaching operating temps.
      Last week, I had the Porsche shop remove the oil pan and check it for any detritus during the PPI. It was clean. Then they proceeded to put on a new filter and oil. I've checked the oil level in the morning, and it registers a smidgen over max, however, the computer level always registers a 1 bar over max, whether hot or cold.  Would a faulty oil level sensor affect the oil pressure reading?
      I've read the oil pressure sensor can be wonky.   I don't have enough miles in this car to really know it yet. It's, obviously, a bit frustrating to keep this car in check while driving right now, but I'd rather cautious. The owner's manual I have says the oil pressure should be approximately 3-4 bars at 5000rpm at operating temperature. Any thoughts? Or direction to go?
    • By Michael hurta
      Hi - 2002 996: Scoured the lists but can't find this particular cluster problem anywhere.  In short, my salvage cluster shows a list of errors on start up but my original was fine....  Here's the details.  My current cluster shows an intermittent airbag failure warning on the led screen followed by the idiot light.  It usually occurs at start up, clears at the stalk and the idiot light remains on, but flickers on occasion.  My mechanic had ruled out everything he could related to the airbag warnings and since he didn't have a spare cluster, couldn't swap to test for that. I personally purchased a salvage cluster, removed the battery terminals, installed it and it came to life (I'm also having to buy replacement connector housings because mine disintegrated).  The problem is the info screen pretty much scrolled through a variety of issues like oil pressure feedback, temp feedback, fuel feedback, etc.  The oil pressure gage was also unresponsive.  I expected the odometer to be wrong, but didn't expect all the errors.  I also started the car and while it ran, it did run rough, sputtered a bit.  Do I have a bad salvaged cluster?  Does the cluster need to be programmed (beside the odometer)?  
    • By Kevin Bryck
      2002 996
       
      Welcome everyone to another installment highlighting the wonderful world of fragile Porsche parts!
       
      Have both 17" and 18" wheels and have recently lost the metal Center Cap logo medallion off of one wheel of each size.
      While removing the other center caps every remaining medallion fell right off in my hand.
      Metal medallion secured with a random dab of some type of adhesive.
       
      We have reached the end of lifespan of whatever adhesive the Center Cap supplier used to keep precious colored metal medallions stuck to those cheap plastic caps.
       
      Anyone know how to remove old adhesive?
      Anyone have any idea what adhesive to replace it with?
      Anyone know how much the Porsche/Piech families made selling replacement center caps last year?
       
      Remember when paying through the nose for your precious replacement Center Caps that the Porsche and Piech families are the 7th wealthiest oligarchs in the world per Wikipedia.
       
       



×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.