Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Hi all,I know that there has been a lot of talk regarding fitting rear speakers to a 981 Boxster . I have a 2014 GTS with sound system plus and I am very keen to add speakers behind the seats to fill in the sound. Is there a way of either enabling the fader on the PCM and then wiring the rear speakers to the amplifier under the seat ? Alternatively,connecting the rear speakers with a resistor of 16 ohms in parallel with the front speakers?
I recently did a suspension overhaul when I replaced my inner CV joints out of necessity. Problem I am having is they cannot align it properly. Because of the lowered suspension and change in geometry the rear toe in is more than it should be. I have ordered a pair of rear control arms from TRS to allow for adjusting toe, hopefully. So now I am looking to replace the Meghan racing tie rods with something that will allow for greater adjustment for proper alignment of the front end. Does anyone have an experience/insight into this type of setup for the street? Can anyone recommend outer tie rods? Will stock factory ones work?
List of what was replaced:
All wheel bearings with *** units repacked with Hi Temp synthetic grease
All 4 struts/shocks with Bilstein B8's along with upper bearings/caps, bump stops, dust boots
All 4 springs with H&R 29779 Lowering springs (Blue)
All 4 lower coffin bars/ball joints with Meyle units
2 rear track arms with units from Vertex auto.
2 rear control arm/ball joint Meyle units.
2 front track arms not sure if Meyle or vertex auto.
2 Inner tie rods
2 outer tie rods with Meghan racing units, adjustable blue color
4 Drop links with Tarrett adjustable units
Eibach 26mm front swaybar along with bushings
factory 19.6 rear swaybar along with bushings
I'm new to the forum here. I have a 1998 Boxster which had been lovely to me until recently when I began experiencing issues with the top. Same story, different time... one of the cables broke, didn't realize it, something got bent. Don't know what. So.. I've disconnected the front arms from the convertible top, and also taken the push rods off of the clamshell so that I can operate it manually. Even with the clamshell operating manually, the clamshell sits ~1-2" too high on the right hand side, and must be forced down! Please don't say the transmissions are not in sync, as this is without even hooking up the transmissions!
I have already replaced the guide arms on both sides as well as the clamshell slides. Is it really possible that the clamshell itself bent? I have already tried loosening all of the bolts that hold the clamshell to the guidearms, and even with shifting that the situation does not improve. The eccentrics on the sliding rails only slightly help it. Can anyone please help? The vehicle has been down for two months as I try and get to the bottom of this.