Jump to content

Server Lease Renewal/Software Licenses

Our yearly server lease, software licenses, as well as hardware operating costs, ARE due Dec 6th, 2021. Our current donations have fallen far short of the funds we need to renew. Please remember the RennTech.org community is Member supported so please consider a donation to help...  THANK YOU!

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

I've read a couple of posts describing other's experiences with engine failure.  My 02 C4 Cab engine lost power, sent lots of smoke out the back and then went silent while in the center lane of 405 south out of Bellevue on a Friday afternoon; just lovely.  I had the car on the side of the road, engine off in about 30 seconds.  Quick check at Chris's German and there's water in the cylinders.  Seems not to matter if cylinder wall crack or other source, an engine rebuild and/or replace seems only course of action.   Given the cost of a factory swap estimated at $36K with refund (~$16k) for core or LN Engineering 3.8 conversion for $15K to $20K the economics just seem out of balance.  I'm looking for lower cost options like a used engine or just sell the car as-is.  

 

Any members have experience with engine replacements or selling a car with an engine in need of rebuild?

Link to comment
Share on other sites

  • Moderators

Selling the car as a "roller" is usually a losing proposition and should only be the choice of desperation.

 

You are going to have to spend some money on a replacement from a wreck, but it is usually the lowest cost pathway to getting the car back on the road.  Shop around for a good used engine in your area, and figure another 2-3K to get it back in one piece.

Link to comment
Share on other sites

My heart goes out to you...that is a bummer, indeed. You are in my neck of the woods, I know the 405 southbound corridor out of Bellevue quite well and I don't know of a worse place to have your car break down...

 

I would be curious to know how this story ends.

 

 

Best of luck to you.

 

Julie

Link to comment
Share on other sites

If I can draw a parallel with selling an old aircraft, the value of the aircraft is 95% into the engine's life left in it.

The 1st thing the buyer will ask you is how many hrs are left to the next R&Overhaul for the engine. This will actually determine the virtual value of your aircraft to him.

 

In your case, your engine has lost most of its value to the buyer and since your car is not of much use without an engine, your roller value is likely around the mid-four-figures, so I'm truly sorry for you.

If you like your car otherwise and want to keep driving Porsches for awhile yet, it might not be a bad idea to contemplate spending 5-figures $ on a reliably-refurbished engine.

At least, you will be totally familiar with the end-product and if you want to sell it at some point in time, your car might still be an attractive proposition after you have enjoyed it for a few years.

Good luck with your tough decision.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Philip Adler
      Since I bought my Boxster the key-fob never worked, so my usual practice
      is to put my key into the cylinder and turn it to unlock.
       
      So this week, I did the procedure I've done hundreds of times, when after opening,
      the resistance I've always felt while turning the lock disappeared! I could now
      turn the key left and right, a full 180 degrees without any resistance. No movement
      in the door latch.
       
      And yet, when I roll the car down the driveway, the door locks do engage and so does the
      latch. Something mechanical must have slipped off the cylinder assembly, and I know I'll
      have to take the door apart to find out,
       
      I'm wondering if anyone has had the same situation and what they've done to fix it.
       
      Thanks1
    • By andrewjt19
      Just wanted to say thanks to the community helped answer some questions about the scoring on my 2008 CTT 957. My next question is, does anyone know where I may purchase a complete engine seals and gasket kit for a 2008 Cayenne Turbo? Or if these are unavailable as a whole unit, had anyone rebuilt their engine from the cylinder scoring or something similar and have a parts list of required seals and gaskets which need changed? Additionally, are there any other suggestions on parts that I should change some I'll have the motor apart? Anything would help at this point. Thanks
    • By StuDalziel
      Hi! I have a 2010 Panamera 4.8l tt that I bought because it had a water damaged engine. Tear down is complete, and I have the parts that need machining at Patterson Elite (http://www.patterson-elite.com). Although I just dropped the parts off today, by this afternoon Todd Patterson had a challenge for me. The block is one solid piece of aluminum (so it seems), therefore the cylinder walls are aluminum and do not appear to be sleeved currently.

      The water damage bent a rod and the result was a scored cylinder, so the challenge is...how do we machine this cylinder? It seems if we follow the standard boring process, when the new pistons and rings go in, the rings will severely score the newly machined cylinder.

      Does anyone have any idea how they built these cylinders at the factory and if this engine can even be machined?

      Thanks!

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.