Jump to content

The RennTech.org community is Member supported!  Please consider an ANNUAL donation to help keep this site operating.
Click here to Donate

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

Hello All,

 

The warning "!" indicated that my License Plate lights are out.  I checked - the bulbs are fine (I replaced with new ones just for the heck of it!). The fuse is OK because when I take the bulbs out and put them right back (like creating an open circuit) - start the car, the message is gone, I check the lights - it's OK (working) BUT as soon as I press on the break to put it in Drive, the message came back on and lights stop working!!! and I can repeat this step!

 

At the same time, when I start the car and drive, the dome light is on until I hit the dome light switch.  When I turn off the car, take key out then eventually the dome light turned off by itself.

 

I don't have any Porsche diagnostic tools except for a generic code reader.  The "Check Engine" light is not on.  Both batteries replaced by the dealer about 20 months ago.

 

My car is CayenneS "04 with 102K mikes on it.  Any suggestions are greatly appreciated.

 

ManN

 

 

 

Link to post
Share on other sites
    You can remove these ads by becoming a Contributing Member.

  • Admin

The system is sensing high resistance. There is a ground point in each rear tail light - I would check those for corrosion. As well remove the license plate bulbs and make sure they and their sockets are clean of any corrosion.

Link to post
Share on other sites

Thanks for the tip Loren. I checked all ground connections, adding additional ground wire on each side of the tail light (just to make sure) and sanded the contact points at the license plate lights, well... that didn't solve the problem! Is there such thing as "light control module" that could be bad?

My next try will be tab on a tail light's circuit to feed the license plate light externally, just for testing purpose. Will this do any harms? or may be I will get another warning indicate that the tail light is failing because it draws more current?

ManN

Link to post
Share on other sites
  • Admin

Well, there is a rear control unit - that controls those lights. I do not know why it would sense a high resistance (the warning light) like a light was out unless there were a damaged connector or wiring somewhere.

It would be very odd for a control unit to only have this problem -- not very likely but I guess possible. PIWIS would be the only sure test.

 

post-1-0-39656000-1433510368_thumb.png

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.