Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)
Martin Bradley

I need to fool my car into thinking the roof is closed - so I can clos

Recommended Posts

I have a broken roof, initially the pivot arm ball joint broke but it turns out this was just a symptom of a bigger problem. Until I can get my roof repaired I need a quick fix to get my windows fully up - I live in Dubai and its 50 degrees!!

I have disconnected the cables underneath the clamshell so that every time I start the car it doesn't try and put it up fully - I have manually put this roof up.

Is there a switch or sensor somewhere that I can lock down or depress or a fuse I can remove which will ignore the roof not up check and therefore enable me to close the windows fully?

Or is there another / better solutions?

Yours meltingly

Share this post


Link to post
Share on other sites
    You can remove these ads by becoming a Contributing Member.

Ok, was my first posting and this may seem a dumb question - but my roof is already up and closed properly - albeit with the error - not in posit. The roof is broken and disconnected - where would there be the red clip you mention?

Share this post


Link to post
Share on other sites

Ok, was my first posting and this may seem a dumb question - but my roof is already up and closed properly - albeit with the error - not in posit. The roof is broken and disconnected - where would there be the red clip you mention?

 

The red clip is for an entirely different purpose, so don't concern yourself about it.  If you have the roof all the way up, and latched,  I'm not sure you can easily by pass the roof position sensors, so I would focus on getting the cables fixed or if necessary, replaced. 

Share this post


Link to post
Share on other sites

Hi, guys - thanks for the response. Roof is up and latched. The pivot arm is broken and the roof/motor/some or all other parts need replaced. I just wondered if there was a way to get my windows up until I got it repaired.

Share this post


Link to post
Share on other sites

Ok, I tinkered around and have found the solution.

I have tried to fix the roof myself a number of times with temporary success and more recently read an article about replacing the whole system. I figured that there must be a point in the motor system whereby it recognizes that the roof is in its closed position either by a limiting part on the motor or by a specific region. So I moved the motor round slowly and eventually the windows went up and the warning light on the dash went off. I only had the drivers side cable connected whilst depressing the window closed arm so I'm not sure if it's just one side where the sensor is (evidence points to this). So my roof is now manually up and my windows are fully closed.

Now I can decide to have another go at fixing or just pay the thousands of dollars to get it fixed by an expert!

Thanks all.

Share this post


Link to post
Share on other sites

At leats in the 996, the final microswitch is often in the latch assembly. There is a piece of plastic that goes onto the hook that sometimes falls off. If your roof is latched then perhaps it is in the clamshell where a microswitch is triggered at the end of the clamshell travel. That is performed by a metal "foot" coming out and pressing the switch.

 

Search my previous posts about clamshell. Hope it is similar.

Edited by 987_RDC

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.