Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Does anyone have or know where I may have the bolt torque specs for a 2008 Cayenne Turbo? I need pretty much the specifications for all the bolts and nuts that would be included in a block replacement. I'm getting the back rebuilt by 928 Motorsports and reinstalling with an experienced friend. However, it's nearly impossible to find the specs for these motors. Additionally, if there's a place where I could find a complete 957 workshop manual, could someone please advise? Thank you.
Pulling the front end on the GT3 to get at a dead horn... found the dust boot on the front strut torn. Has anyone replaced one of these? I had a competition suspension set up from Jae Lee at Mirage in San Diego and don't want to mess it up, but need to replace the boot. Can I just remove the mounting at the top and drop the suspension and replace the boot from the top? ANy help on this is greatly appreciated!
I recently did a suspension overhaul when I replaced my inner CV joints out of necessity. Problem I am having is they cannot align it properly. Because of the lowered suspension and change in geometry the rear toe in is more than it should be. I have ordered a pair of rear control arms from TRS to allow for adjusting toe, hopefully. So now I am looking to replace the Meghan racing tie rods with something that will allow for greater adjustment for proper alignment of the front end. Does anyone have an experience/insight into this type of setup for the street? Can anyone recommend outer tie rods? Will stock factory ones work?
List of what was replaced:
All wheel bearings with *** units repacked with Hi Temp synthetic grease
All 4 struts/shocks with Bilstein B8's along with upper bearings/caps, bump stops, dust boots
All 4 springs with H&R 29779 Lowering springs (Blue)
All 4 lower coffin bars/ball joints with Meyle units
2 rear track arms with units from Vertex auto.
2 rear control arm/ball joint Meyle units.
2 front track arms not sure if Meyle or vertex auto.
2 Inner tie rods
2 outer tie rods with Meghan racing units, adjustable blue color
4 Drop links with Tarrett adjustable units
Eibach 26mm front swaybar along with bushings
factory 19.6 rear swaybar along with bushings
I currently have a 2002 Porsche Boxster S with 86k miles on it. I drive it spirited and do some autocross. I noticed that my right strut started to make some noise and the ride does not seem as firm as it once was. I am thinking about upgrading my suspension with the ROW M030 kit. I am interested in adding a bit more handling while maintaining everyday comfort and drivability. I have read a bunch of articles in regards to all the other parts you should replace when you do the ROW M030 swap. Upon pricing all the parts they are almost 3k!! Here are the parts and pricing I have so far:
202 99734301800 2 - Front Strut Mounts 175.5 98633305906 2 - Rear Strut Mounts 74 99634351505 2 - Strut Bearings (front only) 1795
ROW M030 European Sport Suspension Kit 170 986DLINKF Front Drop Links 170 986DLINKR Rear Drop Links 13 986FRCOMP front compensation plates(size? 3mm or 6.5mm) 13 986RRCOMP rear compensation plates(size? 3mm or 6.5mm) 38 99634350500 Front Shock Bellows 38 98633350501 Rear Shock Bellows 35 99634330102 Front Bump Stops 50 98633330101 Rear Bump Stops
Can you experts please help me determine if I am missing anything else or are there some parts that I just dont need.....
Also any tutorials/advice that anyone can give me would be great.
hey guys , past couple months my cayenne s 04 air suspension warning light has been on, after a minute of driving. when i try lowing or raising the vehicle, the front end works fine but the rear suspension stay stationery in raise mode. even when using the diagnostic to force the rear to lower nothing happens .fault codes in the level control system was for rear suspension holding valve . so i went ahead and replaced both rear holding valve and recalibrate the suspension. it worked fine for two months .now the warning light is back the rear suspension is stuck in high and not lowing.
new fault codes p1780 , 1400
im unsure what to do. do i replace the valve again or is there some else wrong
what do you guys think?