Welcome to RennTech.org Community, Guest
So only managed to see a black square of tape expertly placed over the Airbag light (ON all the time), only because of driving it in the sun with the top down. Been concentrating on other parts of the car.
Any-who, that has lead to seeing that the Seatbelt light doesn't appear at all, and closely related, the horn didn't have a fuse in it at all.
So this has brought up a question, the Codes reported, the electrical drawings (Bentley), ....while they say "passenger" or "driver" side, does this in fact relate to the left and right side of the car when it is the probably more common "left-hand drive"?
Code 30 Ignition Circuit, side airbag passenger................is that actually the right side?
This will not reset with the Durametric. I looked at the airbag connector in the left door, but now I am thinking it may actually relate to the other side of the car, i.e. LHD passenger
Interestingly, the Airbag module wiring, Passenger Side Belt Lock, that wire is cut at the plug and a grafted in wire (plug connected) heads off under the dash somewhere (yet to be traced).
So that Br/Bl wire say passenger, but maybe it relates to the right hand side of the car, in this case the drivers seat.
BTW, the left seat, (passenger), does not have a wire at the buckle, but I think maybe the RHD ROW, or Australian RHD cars didn't have that anyway. Or has been replaced with the wrong buckle.
So maybe the Airbag light was covered to avoid looking for a fault, might be a plug.
Could it be related to the seat-belt buckle, again patched to avoid fixing it properly? The light doesn't even go with the self-test, so could be a bulb.
I have read that the seat belt buckle may not be included in the Airbag ignition circuit for this region.
Horn didn't have a fuse in it. Relay operates with the horn pad, but no horns, so maybe bad horns.
The fuse may also have been removed if it had that bad horn pad issue and going off on its own.
Greetings and thank you for the informative site.
I am a new owner of a 2009 Cayenne base model with dead Horn. I’ve read on the forum of typical failures, including steering wheel wire and two horn units. So far I’ve confirmed the fuse is ok.
Before removing wheel arch covers to test the horns, I wanted to check the relay.
Is the horn relay in the under hood fuse box? If so, which position?
By Schnell Gelb
2001 Boxster S, 3 spoke Steering Wheel.
I'm trying to remove the Airbag to fix a Horn problem. To do the OBC mod you might also need to remove the wheel for some methods.So this issue may have a broader appeal?
The removal Procedure seems simple - Bentley Sect 69-10 has details
I slackened the two T30 x m6, 10,5 ( # 99907318302 ) screws at the back of the Steering Wheel.They were very stiff to start with ,then became easier.I did not use a soldering iron to soften the Loctite on these two T30 screws.Despite many rotations, the screws are still firmly attached to the plate/Retaining Frame with no indication of "letting go".
According to Pelican and at least 1 video there is no need to totally remove either of the two screws - just slacken them. The 2 screws seem to be held captive in the Retaining Frame when they have disconnected from the Airbag assy.
But both screws just spin endlessly and still seem firmly connected to the plate. I assume they are cross threaded in the large plate behind the Steering Wheel(the one held by 4 bolts).
I have tried a wedge between the airbag and the Steering wheel while spinning the screw with a cordless drill. No result.
The remaining option to extract the 2 screws is to drill off the screw heads. This is very difficult because both are recessed and obstructed by the wheel and instrument binnacle !
Does anyone have a less brutal method of removing the airbag with 2 cross-threaded screws ?It is too late to try softening the Loctite now !
I checked lots of other Posts on the airbag/Steering Wheel removal subject but did not find any other examples of this problem. Some have stripped the internal flutes of the Torx head but no cross-threading that I found.
Thank you for any suggestions.
BTW, this was an interesting related link that I seldom see quoted- great photos:
First post here but not new to the vehicle forums. I have an 06 Cayenne S and the horns do not work. I did not check them when I bought it and am still new to the Porsche world. I guess I did not check the horn because I was still focused on the problems it was having with the engine. I ended up swapping the engine and still have the old one on the stand. I may rebuild it some day.
But anyway, the horns do not work right now. I have checked the fuse. I pulled the steering wheel apart and found the wire for the signal. I do get a signal when the wheel is compressed so that is not the issue.
I pulled one of the horns off and checked it on a spare battery by connecting each terminal to the + and -. It seems as though the horn does not work at all. I do know that this is a common issue.
I checked to see if I was getting a signal out of the plug. I checked with a testing light and my meter for volts, amps and ohms. I did not get anything when the horn was pressed.
So I have been looking for a wiring diagram. I don't know if the two posts in the plug are for + and - or if there may be some type of voltage regulation in the signal between the two and the ground (-) would be pulled from the chassis through the bolt.
Does anyone have a wiring diagram for the horns? I would like to see the whole circuit.
Weird behaving horn....driving along fairly smooth highway horn will occasionally beep for 1-2 seconds...no correlation to road condt, frequency, etc...just random.
Going over some really bumpy roads, horn will occasionally beep...or more like a chirp.
Recently noticed now the horn does not work....
Anyone seen this behavior before with suggested things to look for?
I am guessing a loose connection but don't look fwd to trying to trace the wires.
Thanks for any help