Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)
Sign in to follow this  
graylens

Bench testing convertible transmissions

Recommended Posts

Hello everyone,

 

My convertible top broke in "fully up" position recently, with the clamshell at a 20 degree tilt.  Was able to remove the clamshell by getting under it (painfully) and found a shredded motor cable going to the driver's side.  I wanted to make sure that neither of the two transmissions were at fault, so I removed them to examine their gears.  Carefully disassembling them, all the gears appear to be in good shape with no missing teeth, however, when using the old intact cable and using the power drill to rotate the cable, the circular interior that goes into the V-joint does not move at all when turning with the power drill.  Does it only rotate when under pressure?

 

I'm thinking I'm *almost* there and would like to avoid $200-$400 for new transmissions if not needed...

 

Thanks in advance,

Keith Rupp

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Content

    • By Kevin Bryck
      Okay this is REALLY specific.
      The adjustable tension cable on the drivers side of my cabriolet disconnected at the top where it threads (8mm) into the top frame, not at the bottom where it snaps onto the ball.
      The is a larger diameter (10mm?) clean smooth painted hole where the cable needs to thread in, which leads to the presumption that there was a nut on the back side?
      Searched all over including removing driver's side rear 'door' panel and fishing around with a magnet but no loose nut found.
      Looks like getting to back side of this frame casting would entail a major disassembly of the cabriolet top frame?
       
      Also, what does this clip that goes over hydraulic cylinder do?
      Right side clips is in place about halfway down length of cylinder.
      Left side clip was down around the base of the shaft.
      Replacing it where there appears to be a shiny spot looks like it would interfere with the cabriolet top potentiometer arm.
      Right cable threaded into frame at top
      Right cable threaded into frame at top
      Missing cable location
      Smooth clean painted hole in top frame where 8mm cable end is supposed to thread in
      Left cable
      Left upper cable end with 8mm thread
      Clip question
    • By Ronnie38
      My 2001 C4 Automatic had what appeared to slip (over rev) when making scarp turns, decided to replace transmission filter and refill, the first run after 10 minuets the transmission went into limp mode (lights on drive selector started to flash) check engine lamp came on (P0734 and P0734) was read. the reason given was input and output ratio wrong for both codes.
      The Durmatic gave no other info. So I proceeded to  order both input and output sensors. Since I couldn't confirm if a shift selonod was bad. Mean while I am in Cal for the holidays I remembered I moved two of the magnets in the pan there were 4 magnets 2 each in the depressions in the rear of the pan I took one each and moved the forward closer to the input and output sensors.
      Anybody out there have any idea besides taking it to the dealer, at 75 bucks for the 5 liters of tranny oil each time I replace something to help me be smarter?
    • By sld
      transmission selector switch and unit repaired replaced 2 times and now it needs it again.
    • By Toyguy
      I just bought myself my first Porsche, a 1998 Boxster.  I have an issue with the soft top that I'd like to get some guidance on.
       
      The top goes down smoothly with no issues.  It also comes up smoothly until it is nearly all the way up.  Just before the dashboard Top light goes out, there is a pretty sharp metallic twang or snap.  It did this when I was looking at the car before purchase, and it did it again this evening when I put the top up after driving the car home.  I'm assuming it's getting caught on something but I wonder if anyone might have suggestions on what to look at given the late point in the cycle where it occurs?
       
      Thanks!
      Dave
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.