Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
By Tim Lambie (Trailbrake)
Several people have told me that the 996 Dual Sender Oil Pressure Switch/Sensor will directly replace the 987-1 Oil Pressure Switch. Can you please confirm this and provide the part number. I would guess it is 996-606-203-03 but, I would like to be sure.
Additionally, if I am running an AIM dash, should I run the pressure lead to the switch input on the ECU and get the pressure data from the CAN bus or, just leave the switch lead attached and run the pressure lead straight to an analog I/O on the AIM dash.
So only managed to see a black square of tape expertly placed over the Airbag light (ON all the time), only because of driving it in the sun with the top down. Been concentrating on other parts of the car.
Any-who, that has lead to seeing that the Seatbelt light doesn't appear at all, and closely related, the horn didn't have a fuse in it at all.
So this has brought up a question, the Codes reported, the electrical drawings (Bentley), ....while they say "passenger" or "driver" side, does this in fact relate to the left and right side of the car when it is the probably more common "left-hand drive"?
Code 30 Ignition Circuit, side airbag passenger................is that actually the right side?
This will not reset with the Durametric. I looked at the airbag connector in the left door, but now I am thinking it may actually relate to the other side of the car, i.e. LHD passenger
Interestingly, the Airbag module wiring, Passenger Side Belt Lock, that wire is cut at the plug and a grafted in wire (plug connected) heads off under the dash somewhere (yet to be traced).
So that Br/Bl wire say passenger, but maybe it relates to the right hand side of the car, in this case the drivers seat.
BTW, the left seat, (passenger), does not have a wire at the buckle, but I think maybe the RHD ROW, or Australian RHD cars didn't have that anyway. Or has been replaced with the wrong buckle.
So maybe the Airbag light was covered to avoid looking for a fault, might be a plug.
Could it be related to the seat-belt buckle, again patched to avoid fixing it properly? The light doesn't even go with the self-test, so could be a bulb.
I have read that the seat belt buckle may not be included in the Airbag ignition circuit for this region.
Horn didn't have a fuse in it. Relay operates with the horn pad, but no horns, so maybe bad horns.
The fuse may also have been removed if it had that bad horn pad issue and going off on its own.
Hey everyone, i own a 2010 porsche Boxter 2.9L with the PDK transmission.. yesterday after leaving the car for a 4 days i started it and went for a drive.. when i turned it on again, i got a warning message “emergency transmission run” and the car became very jerky through gearshifts and wouldnt accelerate properly.. after turning it on and off the message went away and it drove just fine but then it kept re-appearing mid drives and becomes very jerky and clunky...ive noticed since i had the car that the gearbox was sometimes clunky or would make a noise when changing gear but the dealership said that was fine and normal since its a PDK, the car is at 59,000km so its time for a transmission fluid change... could this be a low voltage problem, or transmission fluid? The reverse gear works just fine.. has this happened to any other owners?