Welcome to RennTech.org Community, Guest
I just finished installing a Kenwood Head Unit and used the Kit210/ M.O.S.T HUR 997 module. The installation is not for the faint of heart. I have installed many radios and worked on mods to my previous Porsche's. This took some serious investigation and decoding to see what wires need to be attached to wires in the harnesses. To some extent I was fortunate that the previous owner had an after market unit installed, but had remove nearly everything.
Navigation ( I located the GPS antenna way back under the plastic cowling between the Battery and Cabin Filter)
Phone (tried to locate the mic in the location of the factory mic, but proved to be too difficult for now. Located to left of the radio bezel by removing the small piece of dash and positioning the clip under that.
Volume and Chanel rotary dials on the Steering wheel multi use buttons.
Now the problems left over:
The Phone buttons don't seem to do anything. I need to use the buttons on the radio when placing/receiving calls. This is not major but would like everything to work as well as if a factory head unit was install. Again, it seems that the steering wheel switches are recognized, but not the phone buttons.
Is this maybe something that needs to be programmed in?
By Tim Lambie (Trailbrake)
Several people have told me that the 996 Dual Sender Oil Pressure Switch/Sensor will directly replace the 987-1 Oil Pressure Switch. Can you please confirm this and provide the part number. I would guess it is 996-606-203-03 but, I would like to be sure.
Additionally, if I am running an AIM dash, should I run the pressure lead to the switch input on the ECU and get the pressure data from the CAN bus or, just leave the switch lead attached and run the pressure lead straight to an analog I/O on the AIM dash.
Hey everyone, i own a 2010 porsche Boxter 2.9L with the PDK transmission.. yesterday after leaving the car for a 4 days i started it and went for a drive.. when i turned it on again, i got a warning message “emergency transmission run” and the car became very jerky through gearshifts and wouldnt accelerate properly.. after turning it on and off the message went away and it drove just fine but then it kept re-appearing mid drives and becomes very jerky and clunky...ive noticed since i had the car that the gearbox was sometimes clunky or would make a noise when changing gear but the dealership said that was fine and normal since its a PDK, the car is at 59,000km so its time for a transmission fluid change... could this be a low voltage problem, or transmission fluid? The reverse gear works just fine.. has this happened to any other owners?
Hi everyone, this is my first post. Ever since I was a kid, I've always wanted a Porsche. 911 is out of my price range and although I think Boxster's are cool, I've never been a convertible guy. So, that leaves the Cayman. I love the look of it and I test drove one yesterday and had a blast driving it. However, I'm very concerned about the IMS / oil starvation issues I've been reading about. The car has 48K miles on it and is listed at $23,999 (the price is somewhat negotiable). It would be my primary vehicle (I also have an 84 Toyota Landcruiser FJ60). However, I work from home mostly and only make one trip to my office weekly which is a round trip of about 90 miles. So, I'll be putting around 6K miles per year on the car. I read somewhere that the odds of actually having a failure in a 2006-2008 was something like 1 in 100, but I've read conflicting information on that. I can afford the payments and to pay more for maintenance than I have on my other cars in the past (Ford, Nissan, VW, etc.), but a total engine failure would be devastating and I don't have that kind of cash lying around (without dipping into retirement savings or something crazy like that). So, does anyone know the real likelihood of failure and if there is anyway to easily determine if the DOF solution has already been installed? Also, anyone have an estimate on what it would cost to install the DOF? There also doesn't seem to be any clear info on rebuilt engines out there. I just see a wide range of estimates from $10K - $20K. 10K might not be TOO bad, but 20K...yikes... If I can't feel confident in the 2007, I guess I'll just have to wait and maybe find a good deal on a 2009+. Thanks :)
first of all, i would like to excuse my bad english, im from germany. My name is Dominic and i drive a Cayman S. I really love this car, but i hate the seats.
I bought a pairs of "König" seats and im about to install them this weekend. The only problem is, no Dealer does the coding to dissable to dissable the thorax Airbags. So i need to add some resistors on the cables.
Can somebody tell me where i have to wire the resistors? I found this topic with the same question, but no answer:
Thank you very much in advance!!