Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)
askopp

Heated Seat Retrofit Wiring Help Sought

Recommended Posts

I am in the process of installing heated seats into my 2000 996 Coupe.  I purchased an aftermarket heated seat package that came with the pads, the wiring and the switches.  I want to use the Porsche factory switches though, and I plan on placing them not in the batwing but in the center console where the two dummy plates are.  I've read Dennis Vogel's excellent write up and searched the forums, but need help with the wiring.  The Porsche factory switch has five leads (ground, three to the seats (hi/low/off?), and one to the relay).  BUT, the aftermarket switch has just four leads  (hi, low, ground, power)?.  And the switches seem to operate differently.  Whereas the Porsche switch returns to "home" after being depressed, the aftermarket switch is more like a light switch (on/off).  Pictures of everything are below.  So, the $64,000 question is, how do I wire up the Porsche switch with the four leads from the aftermarket one?  Do I need to bring another line to the Porsche switch?  If so, where am I tapping it into?  Thanks so much in advance for the help.   Andrew

IMG_4452.JPG

IMG_4453.JPG

IMG_4454.JPG

IMG_4455.JPG

IMG_4456.JPG

Share this post


Link to post
Share on other sites

It sounds like you already know where you want your seat heater switches to be placed, I had a couple of empties on the horseshoe surround so moved mine there...  Made a new bat wing filler.  I like this since all the switches are in one place.  You'll note that I exchanged places with the cubby and A/C control panel.  Again I wanted all the business of switching and controls seamless to one another.  I did have to section the cubby to fit, but it wasn't much good anyway other than a place for your iphone.  

 

gps_final1

 

Share this post


Link to post
Share on other sites

Thanks Loren for the diagram.  This is helpful...somewhat.  My problem is that I have at best only a "dangerous" level of knowledge of schematics reading and wiring.  I found what is likely to be the wiring diagram for the aftermarket switch.  See attached.  Can someone translate this and the Porsche schematic and give me a sense whether I can wire in the Porsche switch instead.  And if so how.  Specifically what wires from the Porsche switch go where on the aftermarket diagram?  Thanks much.  Andrew

IMG_4457.PNG

Share this post


Link to post
Share on other sites

I'm not an expert on electronics, so please use my advice with caution.  I did use Denis Vogel's instructions to install heated seats in my car, and based on that experience, I am offering these suggestions.

 

Here's a link to a picture of the seat heater relay with the wiring:

Seat Heater Relay with Wiring

 

There are 7 wires:

 

Red/White

2 brown

Red/yellow

Yellow/white

Black/yellow

Red/violet

 

The red/white is power and the brown is ground.   The other wires are the control wires from the switches.

 

The red/white wire leaves the relay and goes to a connector that has the wire for routing current through the heating pad in the seat back.  Another red/white wire comes out of the connector and goes to another connector to provide current for the heating pad in the seat bottom.  A brown wire exits that connector and runs to the ground in the relay.

 

I think what you need to do is connect the red wire (which I think is power) in your heating pads to the red/white wire from the relay and the black (ground) wire from your heating pads to the brown wire of the relay.  You want to hook the heating elements for the seat back and seat bottom in series so that the current flows through one and then the other.

 

The control wires will be connected as outlined in Denis Vogels' instructions.

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.