Welcome to RennTech.org Community, Guest
By Charles Bradley
My drivers' side headlight was replaced by the dealership after an accident. It has worked fine for two years since, but recently decided to stop working. I get a "check dipped beam" message on the cluster as a result. The turn signals work, as does a single little light on the outer side of the assembly. The main and high beam do not.
After taking it out to inspect, I noticed that the electrical harness connector on the back was the problem. When I could force it into the headlights socket, the lights all powered up and worked fine, as did the high beam. So a poor connection is the culprit.
One of the tabs on the side of the white connector was broken off, so the connector wiggles in its place. I imagine that the force of the headlight being pushed back wiggled it just enough that it wouldnt' seat into the headlight assembly. But getting that white connector into the socket and then back into its place without being able to get my hand in from the rear of the light was not apparent. I also noted that the insulation on all the wires was terribly frayed and coming off in my hands as I examined it.
But with a new connector in hand, I don't see how to wiggle the old one out. It slides in from the side on the back of the tray holding the headlight assembly, but is blocked from sliding out all the way.
How do I rectify this?
Im working on a unique porsche project and as part of it im looking to use the current (>2016) generation 95B Macan LED HeadLights.
What im looking for is the Wiring Diagram from the service manual program, so i can trace what needs to be connected to where relative to my 997.1 wiring harness.
Yes, im aware this will be difficult. Im not looking to just plug and play.
I already have all the wiring for the 997.1 and 997.2 cars (and a few others)
Can anyone help
I am completely flummoxed by this noise I am getting in my 2004 Turbo Cab. A couple nights ago while driving home with the top down, I noticed a rattle different from the normal sound of the motor and not accelerating/decelerating with changes in engine RPM. It occurred at 1800-2000 rpm and was most noticeable when decelerating in 2nd gear in my neighborhood at slow speeds (~20MPH)... with a helper on the throttle and the engine compartment open, it sounds like it is coming from the right side-top of the engine, around the Hydraulic reservoir. Putting a spanner/wrench on the component and up to the temple seems to have confirmed this as the source. I checked my manual and the Pentosin level (mid range on the HOT side of the dipstick at operating temp) I realize that Porsche recommends checking at 20C but I live in Texas now and that won't happen until November. Just out of curiosity I looked at the clutch reservoir up front and after removing the gooey trim cover, found it leaking (Seeping) from the recently replaced cap and appearing to be overfilled. The car has never really been operated in the 8 years I have had it in particularly high average temperatures, so I am hoping that the front is thermal expansion. Any thoughts on this matter are greatly appreciated... Loren? What Say You??
Thanks in advance,
Odd one for the group here:
I have a 2004 Turbo Cab (manual) with X50 that I have owned since early 2010 and put around 30K miles on in that time (Bought with ~20k miles). I recently found a 2004 Turbo Cab (Tiptronic) with ~29,000 miles that was such a good deal that my parents purchased it. I drove the thing recently while visiting and a couple times in constant-radius turns on back roads, the PSM intervened out of nowhere (The first time it happened I actually thought I hit a shift button with my thumb and downshifted mid corner). Anyway, I got it to intervene once more in a pretty benign turn. There certainly wasn't 7 degrees of slip angle and I have to push my own car much harder (read: screw up the corner entry) to get PSM to intervene. I guess my question(s) is/are this: Is there a difference in the PSM software between the Tiptronic cars and Manual?, a malfunction in the Tip?
Very interested to hear the responses. Thanks