Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)
  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By mikesz
      I recently did a suspension overhaul when I replaced my inner CV joints out of necessity.  Problem I am having is they cannot align it properly. Because of the lowered suspension and change in geometry the rear toe in is more than it should be. I have ordered a pair of rear control arms from TRS to allow for adjusting toe, hopefully. So now I am looking to replace the Meghan racing tie rods with something that will allow for greater adjustment for proper alignment of the front end. Does anyone have an experience/insight into this type of setup for the street? Can anyone recommend outer tie rods? Will stock factory ones work?
       
       
       
      List of what was replaced:
      All wheel bearings with *** units repacked with Hi Temp synthetic grease
      All 4 struts/shocks with Bilstein B8's along with upper bearings/caps, bump stops, dust boots
      All 4 springs with H&R 29779 Lowering springs (Blue)
      All 4 lower coffin bars/ball joints with Meyle units
      2 rear track arms with units from Vertex auto.
      2 rear control arm/ball joint Meyle units.
      2 front track arms not sure if Meyle or vertex auto.
      2 Inner tie rods
      2 outer tie rods with Meghan racing units, adjustable blue color
      4 Drop links with Tarrett adjustable units
      Eibach 26mm front swaybar along with bushings
      factory 19.6 rear swaybar along with bushings
    • By smokeman909
      Hi, I am planning to put back the original OEM front and rear coil springs, because I don't like the H&R springs that the previous owner of my boxster S had put in. How hard is it to do this ? I already did the same job on my 2002 Civic. Will it be the same level of difficulty ? For the tools, I had to rent a coil spring compressor from the auto-store and thats about it.  All other tools I had. When I looked at the Porsche Service Manual, I was a bit scared on all the procedure. Should I expect a lot of surprises?
       
      Thanks!
       
    • By baker_g
      MY 99 C2 sits over 3/4 inch lower in the rear than front when measured from level ground to top of wheel well with consistent tire pressure. Assuming this is the correct way to measure, is this an indication that the rear springs are tired and need replaced? I presume the car should sit level with new springs?. Car appears to be aligned properly although I have not had it aligned in the 2 years I've owned the vehicle.
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.