Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Can I simply remove/pull out the variocam actuator in bank 2 (or bank 1 for that matter) to possibly clean or replace then simply insert back in without doing anything else? I would like to do this to trouble shoot to see if I can get the actuator to engage with Durametric (of course the engine will not be running). If it doesn't engage then I would then move to the the solenoid. I have seen videos where they can be cleaned and start working again however the videos I've seen have the variocam actuator completely taken out and set on a work bench. My concern is if I do this wrong I create a larger problem when inserting back in. Any advice, thoughts, questions or comments?
By Kevin Bryck
Okay this is REALLY specific.
The adjustable tension cable on the drivers side of my cabriolet disconnected at the top where it threads (8mm) into the top frame, not at the bottom where it snaps onto the ball.
The is a larger diameter (10mm?) clean smooth painted hole where the cable needs to thread in, which leads to the presumption that there was a nut on the back side?
Searched all over including removing driver's side rear 'door' panel and fishing around with a magnet but no loose nut found.
Looks like getting to back side of this frame casting would entail a major disassembly of the cabriolet top frame?
Also, what does this clip that goes over hydraulic cylinder do?
Right side clips is in place about halfway down length of cylinder.
Left side clip was down around the base of the shaft.
Replacing it where there appears to be a shiny spot looks like it would interfere with the cabriolet top potentiometer arm.
Right cable threaded into frame at top
Right cable threaded into frame at top
Missing cable location
Smooth clean painted hole in top frame where 8mm cable end is supposed to thread in
Left upper cable end with 8mm thread
My 2001 C4 Automatic had what appeared to slip (over rev) when making scarp turns, decided to replace transmission filter and refill, the first run after 10 minuets the transmission went into limp mode (lights on drive selector started to flash) check engine lamp came on (P0734 and P0734) was read. the reason given was input and output ratio wrong for both codes.
The Durmatic gave no other info. So I proceeded to order both input and output sensors. Since I couldn't confirm if a shift selonod was bad. Mean while I am in Cal for the holidays I remembered I moved two of the magnets in the pan there were 4 magnets 2 each in the depressions in the rear of the pan I took one each and moved the forward closer to the input and output sensors.
Anybody out there have any idea besides taking it to the dealer, at 75 bucks for the 5 liters of tranny oil each time I replace something to help me be smarter?
I just bought myself my first Porsche, a 1998 Boxster. I have an issue with the soft top that I'd like to get some guidance on.
The top goes down smoothly with no issues. It also comes up smoothly until it is nearly all the way up. Just before the dashboard Top light goes out, there is a pretty sharp metallic twang or snap. It did this when I was looking at the car before purchase, and it did it again this evening when I put the top up after driving the car home. I'm assuming it's getting caught on something but I wonder if anyone might have suggestions on what to look at given the late point in the cycle where it occurs?