Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
By Kevin Bryck
Okay this is REALLY specific.
The adjustable tension cable on the drivers side of my cabriolet disconnected at the top where it threads (8mm) into the top frame, not at the bottom where it snaps onto the ball.
The is a larger diameter (10mm?) clean smooth painted hole where the cable needs to thread in, which leads to the presumption that there was a nut on the back side?
Searched all over including removing driver's side rear 'door' panel and fishing around with a magnet but no loose nut found.
Looks like getting to back side of this frame casting would entail a major disassembly of the cabriolet top frame?
Also, what does this clip that goes over hydraulic cylinder do?
Right side clips is in place about halfway down length of cylinder.
Left side clip was down around the base of the shaft.
Replacing it where there appears to be a shiny spot looks like it would interfere with the cabriolet top potentiometer arm.
Right cable threaded into frame at top
Right cable threaded into frame at top
Missing cable location
Smooth clean painted hole in top frame where 8mm cable end is supposed to thread in
Left upper cable end with 8mm thread
By David MB
Help - i have a 2003 Boxter tiptronic s - in great shape other than a shrill loud noise like a Kazoo that only happens above 78mph - it sounds as iff coming from around the mirror area of the windscreen but then occasional sounds like its coming from the speaker area passenger side - that being said could be sound transference. Read a number of blogs about badly fitting windscreen so put tape over top rubber seal and body but still there - - as a say like a kazoo at 78mph with hard or soft top - absolutely driving me mad - any help gratefully received.
After 18yrs my convertible top has finally encountered its first issue. After using this forum (thank you!!) to figure out how to access all of the components (top was stuck in closed position), I found the root of my issue, a bad cable. However, as I was very carefully removing the cable from the transmission, the "clip" which is molded into the plastic cover cracked and is no longer functional (see image). Not really surprising on an 18yr old piece of plastic. The transmission works perfectly and I do not want to replace it, so I am looking for advice on any other ways that I can keep the cable properly engaged to the transmission. Please let me know if anyone else has encountered this and if there are any viable solutions. Thank you!
The convertible top on my '99 Boxster has been acting up for the past few years. Sometimes worked fine and other times wouldn't work at all. I had it looked at by my local shop and by my local Porsche service center. My local shop replaced the switch in the convertible top latch housing (a few years ago) and then the emergency break switch (a couple years ago). This didn't solve the problem. Then a couple of weeks ago the Porsche service center again replaced the emergency break switch, again not solving the problem. Over the past week or so the top had completely stopped working, but then this morning it was working again (intermittently). The tech at Porsche said that everything has been checked (relay, switches, etc.) so he suggests replacing the convertible top motor for approximately $2500. I'd appreciate insights from anyone that has been through this. I see quite a few posts re malfunctioning tops so any info will be helpful.
By Dennis Bergman
does anyone have a wiring diagram for the convertible top? 987.2 boxster. ive narrowed the issue down to (pretty sure) being between the relays tray and actual switch in the center console. ive gone as far as cut the green wire that goes to the top motor under clam shell and put 12v to it, it started to work. ive checked the relays and swapped them aswell and still nothing. ive tested the switch in the center and the green and brown wire switch while pulling the switch up from positive to negative like it should. which make me think its somewhere in between the switch and the relay tray. in process of tearing apart middle console, i add power from right before the relays directly to the wire and it works fine just doesnt seem to get the connection when the switch is triggered.