Jump to content

The RennTech.org community is Member supported!  Please consider an ANNUAL donation to help keep this site operating.
Click here to Donate

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Where is the speed setting STORED for the cruise control?


Recommended Posts

This is on a 2004 Cayenne S Titanium.

 

Question:  Where is the speed setting for the cruise control stored, i.e. in which module? 

When you press the end of the stalk to set cruise control, that value is saved until you turn the car off.  That value must live somewhere.  Where?

 

My issue: 

  • When driving, the cruise control will periodically cancel AND forget its setting
  • The cruise control icon on the dash turns off when this happens, then immediately back on
  • No value is stored in the cruise control afterward (i.e. "resume" doesn't work, I have to set the speed again by pressing the "set" button at the end of the stalk)
  • The steering wheel button lights also blink once when this happens (the ones which are toggled with the redundant buttons on the back of the wheel at 9:00 and 3:00)
  • Notably, if I turn those same steering wheel lights off BEFORE one of these events, they turn on AFTER the event, regardless of the setting before the event, as though there has been a reset of that module

 

To me, this points to a module that stores information that doesn't persist through a restart (i.e. key turned off, then car started).  If I can figure out which module that is, I can be more targeted in my search for the cause.

 

So far, I've tried (unsuccessfully):

  • New brake pedal switch
  • New battery and cleaning battery contacts as well as grounds near battery (so far only those)
  • Re-soldering harness splices in driver's footwell/dead pedal area (two were marginal)
  • Fully charging battery with a CTEK 4.3 (battery drain has not been an issue)

 

 

Link to post
Share on other sites
    You can remove these ads by becoming a Contributing Member.

If I am not mistaken CC control inputs would be stored in the DME. If yours is acting up you may have a DME with an internal short or coding issue. Hopefully you only have a bad switch as opposed to needing a new DME.

  • Upvote 1
Link to post
Share on other sites
On 12/31/2020 at 5:47 PM, GSpence2 said:

If I am not mistaken CC control inputs would be stored in the DME. If yours is acting up you may have a DME with an internal short or coding issue. Hopefully you only have a bad switch as opposed to needing a new DME.

 

Thank you, I hope I don't have a bad DME!  Notably, everything else works fine, I haven't changed anything except the battery, so I don't suspect improper coding.

Link to post
Share on other sites
  • Admin

Sometimes when there is a voltage spike to the system (like connecting a new battery) the programming can get "mixed up". When this happens the best thing to do is have a tech/shop with a PIWIS re-program the affected control module(s). I think it very rare to replace a DME if most everything but one or two items are not working.

  • Upvote 2
Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.