Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
-
OBD II P-Codes - Paint Codes
- Registry
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
4StringBass
-
Posts
8 -
Joined
-
Last visited
Content Type
Profiles
Events
Forums
External Paint Colors
Downloads
Tutorials
Links Directory
Collections
Store
Posts posted by 4StringBass
-
-
56 minutes ago, ECU Doctors said:
Yes,
See here under technical data:
Specialized ECU Repair
Thank you! 😎
-
Does anyone have the DME pin out for 2002 986S manual? It's the multi-plug DME part number 996.618.605.00?
I'm trying to diagnose a potentially faulty o2 sensor but I've only got the pin out for the DME with the single 88 pin connector.
Any help greatly appreciated! :)
-
@Ahsai, thanks for your reply.
Yes, 12V power to the black wire.
I have made a mistake in reading the DME pin 30 to relay, as I was using the 97-99 wiring diagram to figure out the DME and I've actually just been measuring an earth connection 😩
Does anyone have the DME pin out for a 2002 Boxster S? Part number 996.618.605.00?
-
Hi,
We recently got P1276 "Fault Code 22, signal delay time for oxygen sensor ageing, bank 2".
The sensor got replaced and within 50 miles it had thrown the same fault code again. I reset it, and it was 100 miles before it tripped the CEL this time.
Hooked the Durametric up and went for a drive. There is no resistance showing on the bank 2 plug (see attached image). Everything else was roughly the same for bank 1 and bank 2 as we were driving.
I have done a continuity test between DME pin 30 and the oxygen sensor relay pin 87 as per the workshop manual for both sides of the car, with one sensor unplugged each time and it seems OK, it's not an open circuit. There is approx the same resistance in the heater circuit of both pre-cat sensors when measured from the sensor plug.
What other resistance in the system looking for?
What can I check next?
I'd rather eliminate everything before throwing another sensor at it.
Thanks in advance!
-
9 minutes ago, Loren said:
Try 9161
THANK YOU! ?
-
Hello,
I've locked myself out changing the ignition switch if someone could please help :)
CDR-22
4467
serial: 15004793
24/99
Thank you!
-
Hello all,
Yesterday the wife took her 986S for a run and the wipers stopped working. When I went to put the car in the garage, they moved to the top of the sweep and stopped, and when I went to turn the car off, they almost went all the way down but not quite. The screen wash isn't working either. Car is a UK RHD 2002 986S.
I've checked the 25A fuse and it seems ok, and I've pulled the intermittent relay out and that's made no difference either. I did read on another thread here that the wipers should work on/off without it fitted.
I have found loads of info on here about wipers playing up but nothing that answers this specific issue :)
Where do I look next? Control stalk?
Thanks
P1276 even after sensor changed - showing 0 resistance
in 986 Series (Boxster, Boxster S)
Posted
@Ahsai, you're a legend. It's the rear sensor reading a tenth of what it should be.
Thanks again.