Server Lease Renewal/Software Licenses - Goal Reached!
A big Thank You to all those that donated to help us reach our 2019 goal (and pay the site operating costs)!
Just an FYI - if all members of this site had donated - then the cost per member would have been less than $0.06 each.
Thanks again to all of you that did contribute!
Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Yes all good :( would've been an easy remedy
Yes all good :( would've been an easy remedy
Don't have any knowledge on sensors or their specific locations is there a schematic or layout I can try to find . Thank you again for your valuable response
Hi motor was scored and damaged engine was completely rebuilt and tranny also dropped and removed some sensors were replaced I believe not sure as to which ones tranny is a manual scanner doesn't show any DTC's thank you very much
Thanks Richard for the response. I never touched the instrument cluster but will check it thanks
After install of rebuilt engine, tach, odometer , speedo not working all else works fine , guessing we missed installing some wiring to tranny ? Any suggestions Thanks
demarconstruction started following 1999 carerra c2, 99 996c2 issues with instrument cluster, 99 carerra rebuilt engine with mods... Curious about projected horsepo and and 1 other
Thanks everyone for replies. Muffler hanger did catch one of the wires
Hi guys, looking for any input or comments on what power/performance I should expect from a new rebuilt on my 99 C2 3.4 to a 3.8 liter Jason from UFO Motorsport in CA performed the work . Included in the rebuild was Nickies , raised compression to 12:1 polished ports(350hp) Ipd plenum ( 28 hp) , k and n air kit( 23 hp) NHp full exhaust system ( x51 headers, 200 cat x pipes w/ mufflers 30+hp) horsepower listed after each mod is the advertised increase . I've read that these hp increases are not realistic but would appreciate the input from this forum as I will eventually have the car dynoed once Ecu is tuned . Thanks in advance
Recently installed rebuilt engine and now speedo,tach and odometer not working digital also not working . Fuses are good . Any suggestions. Thanks
Hello all Just recently installed a newly rebuilt engine and upon 1st start up the C-2 fuse( ignition, fuel injectors, 02 sensor) keeps blowing all wiring was reinstalled as removed and new engine was run and tested anyone have any suggestions please help Thanknyou!
Thanks JFP, was just speaking to Jake earlier today. Not sure I want to Invest close to 20k but It Is an option. Atleast I know I will get my engine back and In great shape with Jake. The other guys..... not so sure
Hi Everyone, Looking for a reputable engine rebuilder for my 99 c2 3.4, I believe engine has a cracked cylinder or sleeve , was actually ready to pull the trigger and have Motor Meister do the rebuild and big bore to 3.8 but checked into their past and found alot of complaints and unsatisfied customers. Im located on east coast (NY). was also looking for some performance upgrades. Engine is out of car and ready ! Thanks
demarconstruction replied to demarconstruction's topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)Thanks for both your Inputs. Will most likely go with Lorens fronts and rear tire sizes. Thanks again you guys are really great!
Hi All, Looking for Input on installing wider tires on my 99 C2 , Have 18" x 10" rims ( measured the width with the tire on and it was approx 11", outside bead to outside bead) that currently have 265 35 18's at the rears and front are 225 40 18's . Fronts I am ok with but would like to add some width to rears without changing rims. Was hoping to go from the 265 to 295 or 305. Any suggestions? Thanks Dean