demarconstruction

Yes all good :( would've been an easy remedy

Yes all good :( would've been an easy remedy

Don't have any knowledge on sensors or their specific locations is there a schematic or layout I can try to find . Thank you again for your valuable response

Hi motor was scored and damaged engine was completely rebuilt and tranny also dropped and removed some sensors were replaced I believe not sure as to which ones tranny is a manual scanner doesn't show any DTC's thank you very much

Thanks Richard for the response. I never touched the instrument cluster but will check it thanks

After install of rebuilt engine, tach, odometer , speedo not working all else works fine , guessing we missed installing some wiring to tranny ? Any suggestions Thanks

Thanks everyone for replies. Muffler hanger did catch one of the wires

Hi guys, looking for any input or comments on what power/performance I should expect from a new rebuilt on my 99 C2 3.4 to a 3.8 liter Jason from UFO Motorsport in CA performed the work . Included in the rebuild was Nickies , raised compression to 12:1 polished ports(350hp) Ipd plenum ( 28 hp) , k and n air kit( 23 hp) NHp full exhaust system ( x51 headers, 200 cat x pipes w/ mufflers 30+hp) horsepower listed after each mod is the advertised increase . I've read that these hp increases are not realistic but would appreciate the input from this forum as I will eventually have the car dynoed once Ecu is tuned . Thanks in advance

Recently installed rebuilt engine and now speedo,tach and odometer not working digital also not working . Fuses are good . Any suggestions. Thanks

Thanks JFP

Hello all Just recently installed a newly rebuilt engine and upon 1st start up the C-2 fuse( ignition, fuel injectors, 02 sensor) keeps blowing all wiring was reinstalled as removed and new engine was run and tested anyone have any suggestions please help Thanknyou!

Thanks JFP, was just speaking to Jake earlier today. Not sure I want to Invest close to 20k but It Is an option. Atleast I know I will get my engine back and In great shape with Jake. The other guys..... not so sure

Hi Everyone, Looking for a reputable engine rebuilder for my 99 c2 3.4, I believe engine has a cracked cylinder or sleeve , was actually ready to pull the trigger and have Motor Meister do the rebuild and big bore to 3.8 but checked into their past and found alot of complaints and unsatisfied customers. Im located on east coast (NY). was also looking for some performance upgrades. Engine is out of car and ready ! Thanks

Thanks for both your Inputs. Will most likely go with Lorens fronts and rear tire sizes. Thanks again you guys are really great!

Hi All, Looking for Input on installing wider tires on my 99 C2 , Have 18" x 10" rims ( measured the width with the tire on and it was approx 11", outside bead to outside bead) that currently have 265 35 18's at the rears and front are 225 40 18's . Fronts I am ok with but would like to add some width to rears without changing rims. Was hoping to go from the 265 to 295 or 305. Any suggestions? Thanks Dean

Hello recently replaced the panels for the electric adjustment for the front seats but am having a difficult time trying to reinstall the panel to the actual switch which has small internal switches that regulate the seat adjustment ,If not put on perfectly the seat doesnt move properly, anyone have a diagram or suggestions Thanks!

yes all good

Hello all, I am need of some help with my newly purchased 99 carrera i am replacing the drivers front seat and cannot get at the rear torx bolts the seat will not move forward as im guessing the motor is dead ?? Is there a manual way of moving the seat forward Thanks for any help in advance !!

Hello Hope everyone Is well, I am In need of getting my gas tank posibly repaired , I noticed a good leak coming fromthe gas tank looks like ran over something and it hit the tank as the plastic covering has a 3" x 5" crack in it and has damaged/ cracked the tank . Does anyone know If this is something that can be repaired or pricing on a replacement tank Thanks for any help Dean

HI all I had posted an earlier question about the shift linkage for my 04 cayenne tt seems the small plastic nut?? broke off shift cable that goes to transmission arm under car and i had to order the shift cable in order to replace It the factory part # 955-426-033-11 im just not sure how to remove the casing around the auto gear selector in car anyone know the removal and install on this Thanks In advance Dean

hello all have a small problem car tranny selector isnt doing anything when moved from park to drive or reverse and can hear some small noises like its not connected to tranny armi looked under the car and can see that the gear selector arm isnt connected to the gear shift for the tranny its a small plastic nut can anyone tell me what this is called or a part number thanks

yes i thought so also but It didnt give me the option too

ok thanks

Also there arent any lights on just saw this code after we scanned it with the scan tool does that make any difference? and by driving the car can we do any damage/ thanks

Thanks for Input, It was running rough and kinda "bucking" when i accelerated hard on it so we changed the plugs and coils and that has stopped the so-called "bucking" Thought maybe a battery diconnect could help, anyone know If ther is an easier way of cutting the battery power other than removing the front seat? Thanks