Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

dension needing unswitched power

markj911
 Share

Recommended Posts

markj911 Member

markj911

Posted
Posted

Hi Everyone,

I have combed the site (and rennteam as well) to understand where I can tap into an unswitched 12V source near the NAV to install my Dension 500 without success. I have seen a few posts where installers use the power feed to the CD changer but no clear indication that it is unswitched. I have a very early 05 997S

Cheers,

Mark

Link to comment
Share on other sites
AP 997S Member

AP 997S

Posted
Posted
Hi Everyone,

I have combed the site (and rennteam as well) to understand where I can tap into an unswitched 12V source near the NAV to install my Dension 500 without success. I have seen a few posts where installers use the power feed to the CD changer but no clear indication that it is unswitched. I have a very early 05 997S

Cheers,

Mark

Hi Mark,

I too have an early 05 997S. I installed my Dension close to 2 years ago and used the CD changer power harness as the source to my Dension. My 997S didn't have the changer but the harness/connector was there. To be honest I don't recall (my brain cells need an unswitched power source as well) if it's switched or unswitched but that should be easy for you to determine by test. In my case my IPOD is always connected and it's never had a dead battery so I suspect the CD changer power might be unswitched.

Good Luck w/ the install.

Arnie

Link to comment
Share on other sites
berty987 Member

berty987

Posted
Posted

I have a dension unit fitted in my 987S. The front luggage compartment is identical to the 997 so the wire tapping points are the same. The CD changer has a permanent live feed as does the navigation unit. From memory I think the power is the green red wire and the brown is the earth. I did a little write up on the 987 forum , you may want to take a look.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.