Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Had the exact same problem and it was the fuel pump you're describing. Right after that, the purge valve failed too. That was an easy DIY.
My 04S with 117K miles has done this for 5 years. Not planning to do anything until it fails.
Control module was bad. 335+/- and three hours labor @135 per hour. Time to sell. Done with this brand.
Dropped the car off at the dealer yesterday... Wow! One hour of labor later 135.00 US and they don't know what the problem is. They can "see" the seat control module but don't know why it's not responding to input. I asked what was done to consume one hour of labor. I was told the tech checked the fuses, and tried to communicate with the seat via the computer. Does that really take an hour? It took me ten minutes to find out that I couldn't communicate with the seat module with my Durametric software and less than two minutes to check the fuse panel. Next step is to remove the seat... Anyone know what "the book" says to remove the seat? And I do mean remove. All four bolts. The seat back cannot be moved because it's inoperative so for them to check the wiring under the seat, it must be removed. "Maybe with another hour of diagnosis we can find out what the problem is" sure sounds like they're wanting to run up the bill because I attempted the repair myself. Any input? Thanks!
Re: Changing oil to remedy codes... My service writer in Austin had told me the same thing about a camshaft position sensor problem. Seems even the techs think the recommended oil change interval is too long in general. Not stating any facts. It's not the first time I have heard "change the oil" to solve a senor problem before. $0.02
So... upgraded my Durametric to V6. I already had the correct cable thanks to buying it back in late 08 when the 2nd gen cables started being sold. Fire up the car and get the software up and running. The "Seat Memory Driver" tab will allow me to click on the Identification feature and a part number shows up with two other bits of info. When I click on Output Test to test the control of the seat motors etc after the warnings are agreed to, all I get are "greyed out" buttons for "Start/Next" and "Skip Actuator" but the "Done" button is the only clickable button there. I waited about thirty seconds. Do I need to wait longer? I have no idea what the Adaptation feature will allow me to do and cannot find any info on it from Durametric's website as their software suggests I visit their Adaptation section. Time to open a support ticket with Durametric? Any help is appreciated.
Thanks wvicary. How do I communicate with the seat module? Durametric? I'm not a pro and don't have the Porsche computer. Many thanks! KR
Hello all! I've a problem I cant seem to solve. 2004S with 110K miles Drivers side seat position inoperative. Bought a new switch (I know I got the right one since we used the VIN to order the switch for my car with the correct options) and started the install. Found 4 broken/severed wires in the harness that goes to the switch itself. These are very small thin gauge wires as you will see in the photos. I've repaired the broken wires by soldering them back together and using heat shrink tubing on them, wrapping them in tape and then conduit. Hooked up the harness to the switch to check for operation. No response from seat. The 30 amp fuse is not blown and has continuity. I have 12 volts to the fuse as well. Is it possible that in the process of those four wires getting damaged/severed and NOT blowing the fuse that the black box seen in the photos has been damaged? What is that black box? I'm at my wits end to get some repsponse from the seat and don't know what to do next. Does the seat have to be in its installed position to get proper ground for the position selector to function? Is that my problem? Any help is much appreciated!
Watch the video you'll find here... the window struts are adjacent to the gate struts.
There are clips on each end of the ball/sockets that "pop" out of the way. Once removed the strut comes off. Pop on the new one. As mentioned, it really is a three minute job. Slide the seat all the way back so you can get comfy looking under the steering wheel. You'll see it. A small flat blade screwdriver is needed to remove the clips. Cheers
rizzo replied to TopGun2000's topic in 9PA, 9PA1 (Cayenne, Cayenne S, Cayenne Turbo, Cayenne Turbo S)Michelin Energy for me. Very quiet compared to the original Conti's 35K miles into the 40K warranty and still more than half the tread left. 265 per in general right now.
04 Cayenne S and I have been having the same problem. Managed to break the mounting plate trying to get the lever to seat properly last time I had the assembly out. Front right turn signal sometimes fails to energize and I get the dash alarm about check indicator lights. Run over a bump down the road after a restart and they work for several days... Try the cleaning as suggested here. Then try some profanity if you break the mounting plate like I did.
What about the "kazoo" sound the moment after the starter motor has finished igniting the engine? Mine still does it from time to time...
Doing a pad change is easy. If you need new rotors, the tools to remove the calipers may cost you a bit on the front end. If you have all the tools, time, and experience to DIY it's worth every dime you'll save in labor and parts at the dealer. $0.02