Server Lease Renewal/Software Licenses
Our yearly server lease, software licenses, as well as hardware operating costs, ARE due Dec 6th, 2021. Our current donations have fallen far short of the funds we need to renew. Please remember the RennTech.org community is Member supported so please consider a donation to help... THANK YOU!
Welcome to RennTech.org Community, Guest
External Paint Colors
Porsche TSB Listings
Everything posted by parabolic
Welcome :) ... I wish you the best of luck with your Porsche..... you´ll have plenty of fun filled DIY hours with these cars ..... :)
.... is there a coolant smell coming from the engine bay ? Could be coolant fluid from busted plastic coolant pipes/T´s --- the coolant fluid is also red (and ´oily´ ) .... That or transmission seal....
The Durametric readings look good. The cam deviation stays constant at -1 ca and +1 ca - throughout all rpm´s. Actual cam values are properly synchronized between banks at all rpm´s - 0 deg at idle up to 30 deg. So, there are no apparent problems there. The interior of the engine looks VERY clean - the oil change service book shows an irregular but acceptable oil service interval. When i purchased the car I initially did an oil change with M1 0-w40 and again 5k km later - to Motul 300v 5-w40. My next change will be to Mobil-1 5-w50 (Rally formula). I´ve also used Liqui-Moly Ceratec and that did quiet the engine down considerably. The thing is, I am far from being sure the rough idle and knock has anything to do with the chain - but in my mind it was the only diagnosis that fit both symptoms. Probably the best action would be to take the valve covers off and run a borescope down the chain housing. Maybe do the tensioner while at it. Probably the knock and idle issues are unrelated - could be the poor thing just needs thicker oil and a new fuel pump :)
I haven´t checked the fuel pressure....if there was a problem with a fuel pump, wouldn´t it be apparent at higher rpm´s also ?
Royxaxa - I read your description regarding the timing chain swap - and I was partially basing my assumptions on your writeup regarding the stretched chain and broken guides. I also spoke to the local Porsche workshop manager - who said the tapping noise was unusually heavy, and he agreed that the engine idle was indicating timing problems. This engine is now at 150k km - and I was leaning towards the chain as the culprit. The strange thing is that the bad idle comes and goes - randomly. There are no preset conditions that trigger the bad idle - but the tapping noise ONLY appears with the engine at full operating temp. Maybe I need 5w-50 oil for this engine for the tappets at operating oil temp.? I´ve recently changed the oil/filter (Motul 300v 5w-40) - waterpump/thermostat/cooling pipes - PCV is new and I´m about to change the diverter valves. There are no apparent vacuum leaks and the engine seems to run fine otherwise. What I haven´t ruled out is MAF´s - pre-cat Oxygen sensors - Coils. But there are no misfires or fuel mixture anomalies according to the durametric readout. The only other issue is that the engine ´chokes/hesitates´ on quick throttle from idle.
I've been having issues with rough idling and a slight 'knock' sound ( at full operating temp only )in my 9pa Cayenne Turbo.I've checked the cylinders (boroscoped) for damage and compression tested- and there is no cylinder scoring or leakage. Spark plugs have been replaced - and coils look fine (03 rev coils). No fault codes in engine module.I'm currently leaning towards a timing chain issue - whereas the knock sound is a result of a broken timing chain guide and/or stretched chain.Using durametric the cam deviation is reading a steady +1 ca / -1 ca. Actual cam timing is relatively synchronized between banks at all rpm. Can anyone give me pointers as to what I should be logging with Durametric - so that I can post the log here for help in diagnosing this issue. ?
Solved this issue.... after tearing the cooling system apart , I found the new replacement 3pcs aluminum coolant pipes had a manufacturing defect.... and the pipe feeding the heater core was physically blocked. Sure...... I should have blown into the pipes, or somehow given them a better inspection before installing.... but somehow I ´assumed´ these parts were quality controlled before sale... Note to future installers; check the pipe throughput before installing... :rolleyes:
I just did a complete fault code readout with Durametric and I´m getting a Gateway fault code: 1320 Air-conditioning system regulator control module - No signal communication etc..... Is there HVAC controlled valve that controls the coolant flow to the heater core ? Are there any cooling system schematics for the Cayenne that could help diagnose the issue ? Edit: Just ordered a new water pump and a Uview Airlift II - It costs me more to have the car sitting around for a month then the price of the parts. I'll post an update when I know more.
Never underestimate the power of sun visor flipping.... B) Electric pump reinstalled and primed - still no heat in cabin. I´ve yet to rule out the belt driven water pump. This car has 150k km on it - and to my knowledge, the water pump has never been replaced. I pulled the upper vent line from the coolant reservoir with the engine running - and there is significant coolant coming out when idling - even more when reving. So the question is; how much is enough ? What other procedures would you recommend in troubleshooting the belt driven water pump?
I pulled the additional (electric) water pump today - and it´s working 100%. This type of pump is very susceptible to cavitation if there is not enough pressure on both ends. But this pump is definitely NOT the problem. Before pulling the pump, I ran the engine to full operating temperature - but to my surprise the lines to the electric pump did not heat up at all. Tomorrow I´ll try to prime the heater core by disconnecting the re-tour hose and see if I can get the pump to recirculate through the lines. Regarding the main belt driven pump; I´m pretty sure it´s functioning as it should - since the radiator hoses are well pressurized while the car is running. And there is throughput in the reservoir while reving the engine. I´ve talked to several people who are all telling me the same thing - rev the engine in an incline - top up as needed - take a spirited drive - top up. But it´s just my luck that it doesn´t work for me :)
Ok, next step is to put gradual pressure on the coolant expansion tank, so I have a few questions: 1. Would compressor air suffice - or should I push coolant in there ? 2. What would be the max pressure I should put on the system ? 3. Engine/electrical pump running or not ?
If the system doesn´t purge by itself over the next few days - then I´ll remove the pump and test it. Maybe I´ll also try to prime the radiator core with coolant. Judging by the diagrams I can´t see any valves between the auxillary pump and the radiator core - so there shouldn´t be any problems putting external pressure (15-20psi) into the auxiliary water pump junction ? Water pump in question # 955 106 561 01
The pump does run - I´ve started it and can hear it run by actuating the "Rest" feature - and also via Durametric. Since the coolant sensor isn´t at the top point of the cooling system i´m a little baffled by it´s fluctuation. Maybe I could remove the sensor itself to purge the air from that manifold? Or, instead of chasing my own tail - I could have the coolant refilled by a shop equipped with a vacuum filling system. The techs I´ve spoken too have all said they just fill the reservoir and then warm the engine - wait till cold - then add coolant....repeat as necessary. Most were very surprised that the system hadn´t purged the air by now.....since i´ve run the engine both stationary and driven the car for a few runs.
2003 Cayenne Turbo - Cold climate package It all started out with the classic failure of the plastic cooling pipes. My wife was driving the car when a severe coolant leak emerged - and after the failure she "had to" drive the car a few more minutes before stopping. What happened in those minutes will never be entirely clear ..... so be it. When I arrived at the scene to access the damage I switched on the car (without starting) to hear a DRY pumping noise - and immense rattling coming from the driver side fender. Clearly an electrical (additional coolant pump) running dry, so I just switched off the car and had it towed. 10 days later I finished the coolant pipe upgrade/repair and refilled the cooling system without using the vacuum filling procedure that is recommended by the workshop manual. Result: No heat coming from the cabin heater. So I suspected some air blockage in the system. But after following the workshop manual bleeding procedure - and other maneuvers, s.a. lifting the front of car while reving engine/removing driver side radiator hose etc/running pressure through the system etc = no improvement. Also, the engine heat gauge is overly hot when idling - but returns to normal under higher rpms. So, is it possible the the additional water pump has failed ? Is this pump feeding the heater core and the heat sensor cooling manifold ? Is there other likely cause for this failure ? All and any help would be appreciated :)