Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Ca Bill replied to Ca Bill's topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)Need help finding cabriolet top sensor's locations, so I can check one by one .
The top on the car is stuck in the open position and I can't get it to close . It will starts to close and the clam shell and the flaps get fully open and out the way, then every thing stops all I hear is clicking after that ( electrical sounds ) . I tried to calibrate with Durametric but every thing stops at the same point . I even tried to manually to close the top but it only left 4 inches and I don't wont to force it or break any thing . Is any one out their have the proper procedure to close it manually so I can go though and check the oil level and sensors . I did removed the back cover to access the pressure relief valve for the pump and that how I can left the top only 4 inches . Any suggestion would be helpful. Thanks in advance for all your help.
Ca Bill replied to Ca Bill's topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)Thanks for the fast respond , I have to track back and find out when and where it was replaced ,
Hi Every One and Happy New Year , As I was changing my spark plugs and coils I noticed my engine Id numbers , so tried to match it with the under the hood and its different. Under the hood says its M96/0366Z.... and on the Engine says M96/04Y14023. So my engine had been replaced some time ago . Not bad thing in my book . so what year is this engine was manufactured? I have 2002 Cab . 6sp . Thanks .
Thanks for all the responds , The module is installed and it only took very short time , I installed it on the upper light do to city driving , No resistor was needed and the cruise control works flawlessly , After installation drove the car to city Police Department and asked to speak to officer on duty, to find out if it's going to be problem . after he looked at it he brought out his Sargent who was 2005 997.1 owner to find out where I bought the module because he wont one to install on his car. I was assured it was legal and few of the new cars already have that feature. Again Thanks for all the support .
Need Help again , working on my02 cab, won't to add strobe module to my third brake light, Do I need to add two modules one for each ,or can I just add one to the main third brake light wires ? I have been searching for the diagram. and the location of the main wires . Thanks for all the help.
Ca Bill replied to Ca Bill's topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)Thanks for the respond, I used the factory wires and it sound great .
Ca Bill posted a topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)I have 2002 cab with factory amp that I am replacing a 6x40 none Bose , replacing it with after market 640 amp 5 CH. The question is do I need to rewire my door speakers ?? or can use the old wiring? going from 2 ohms to 4 ohms , Or I can take out the inline capacitor if their is one. I already replaced my head unit and the all the other speakers . and if their is capacitor where is it located . Thanks
Ca Bill replied to steve20186's topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)I also get that when I am running around and doing short stops.
Ca Bill replied to RHP_CO's topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)Hi Rob, What is the color of the security wire , Because I have the same issue and how to correct it , just disconnect all together? I did my own install on my double din . Thanks . Bill
Ca Bill replied to huesey1974's topic in 996 Series (Carrera, Carrera 4, Carrera 4S, Targa)Hi, The black plug goes on the bottom.
You need nothing , I just finish adding Double Din and Nav. in my car . The cd holder and the climate controller is the same size and the harness is long enough . Bill.