Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Search the Community
Showing results for tags 'pulley'.
Found 5 results
I need to remove the crankshaft pulley from my 2000 C2 Cab. Does anyone have tools 9285/1 and 9290 that they would like to sell?
I have a 2003 Boxster with 77,653 miles. I am the third owner and this Tiptronic Porsche was brand new in late December 2002. It is my daily driver and most of its miles are on the highway. It hasn't been tracked. Roughly two weeks ago the coolant temperature blinking light came on for roughly a minute. It has come on once since then. Each time the engine temperature was perfectly fine throughout the 1 1/2 trip. I did not until today check the coolant level (my bad) and now see that the fluid is well below the minimum level but can be seen when looking down through the opening. On the way home from San Antonio for Thanksgiving I heard a new cyclical noise that sounds like bearings going out. I've read up on different websites that it is likely my alternator, pulleys, or water pump. My battery registers 12.6 volts when the engine isn't running and 13.93 when it is running. I bought a mechanics stethoscope and as best I can tell the water pump and the lower pulley seem to have rough noises. And there does seems to be the smallest flutter in the water pump pulley with it going in and out maybe 1 to 2 mm. Here's a link to a short video ( ) of the engine running and you can hear what I think is a bearing going. Would the next step in isolating the problem be to remove the drive belt and try spinning the pulleys and water pump pulley freely to see if there is any obvious failure going on? I tried the WD-40 trick but spraying it on the pulleys while running didn't make any obvious difference. If it is the pulley and/or water pump how difficult are those fixes if I'm handy and have in the past replaced a turbocharger on my old Saab 900? I don't fear much in the way of fixes (perhaps to a fault). Please share your wisdom or I'll end up spending too much at a shop. :-) Thanks, Trevor in Austin
MY 2000 - 996 Cab with 54K miles Should the pulley on my power steering pump spin as freely as the pulleys on my alternator and water pump? I have been trying to track down a high pitch hum/squeel at certain speeds and I checked the pulleys today. The pulley clearly doesn't spin like the others. I checked this last winter when I replaced the water pump and I don't recall any tension in the spinning of this pulley at that time.
Hi. I was supplied with a replacement (recon) alternator for my 2002 Boxster S but it had the solid pulley fitted instead of the freewheeling / overrunning clutch type. My garage fitted it anyway but found that it only charged at 8.4 volts. The alternator supplier is telling me that the reason it only delivered 8.4v was due to the incorrect pulley being fitted rather than any internal fault with the alternator which I find difficult to believe. We fitted another alternator with the correct pulley & this one charges fine. Has anyone any experience of running a "solid" alternator drive in place of the "freewheel" type please? Does it in fact result in a lower charge output or is this a red herring by the alternator supplier to avoid picking up the second set of labour charges. Thanks
99- 996 with trip. With the help of the forum (quick thank you) I was able to determine that I had a bad bearing/idler pully. I have removed the air box and am trying to determine: 1. the correct torque for the attaching bolt on the upper idler, and 2. does it require a specific spanner or wrench, or can i use a common open/box end? Also there was a great video (shows removal of box and how to on the tensioner) when I first looked at how to do this but I have since grown a few days older and cannot remember the search words i used. Any ideas? Thank you in advance for your help. Serg