Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Engine Temperature Light


Recommended Posts

My engine temperature light (the light next to the 250degree mark) keeps flashing at me. This has started only recently and since the manual that I recieved upon purchasing the car was stuck together (pages got wet) I do not know what that light means.

Problem: The light on the engine temperature gauge is flashing (not rapidly, just on, off, on, off)

Details: My car is not overheating, the temp stays just above 180, in normal range 12'o'clock position.

What does this mean? How do I fix it?

Edited by DaemonRa
Link to comment
Share on other sites

Do you know what kind to use and where to get it? dealership wants $50

It's expensive but using another type will likely turn your coolant into jello.

If you're adding coolant, the mix is 50/50 (half coolant, half DISTILLED water)

If your tank is dry you'll likely want to burb it via the bleeder valve after filling to be sure there isn't an air pocket.

Since you are adding coolant you'll want to find out were it went.

Link to comment
Share on other sites

  • 3 weeks later...

Update:

The check engine light went off and I am currently doing my 60k service. However, I have an idling issue. I've read from other posts on this subject that the boxster idle should be around 700 or so. Mine is about 600 or perhaps a bit less ( slightly less than halfway between 500 and 750 ). When I start the car it idles just fine at about 1000rpms and after that disengages it idles at about 700 for a few minutes then lowers again after driving. It became a place of interest when I turned my lights and fog lights on simultaneously and I heard the engine bog down to just below 500 rpms and then it caught itself and adjusted.

Question: What could this be?

Question 2: Do any of the issues associated with the check engine light that came come correlate to this issue?

Question 3: How do I fix it, what is the part number?

Edit: This is attached to the wrong post, oops. Sorry. Here is the back information about the check engine light thing:

P1126 Oxygen Sensing Adaptation, Lower Load Range, Bank 1 – Above Limit

P1133 Oxygen Sensing Adaptation, Lower Load Range, Bank 2 – Above Limit

Potential causes:

– Incorrect signal from MAF sensor

– Intake air system leaking

– Fuel pressure too low

– Volume supply of fuel pump too low

– Fuel injectors fouled

Edited by DaemonRa
Link to comment
Share on other sites

There is a lot of suction when I remove the oil filler cap. Also the radiator cap is leaking, need to be replaced and part is in mail.

You didn't state the mileage on the car, but excessive suction on the oil filler cap is usually an indication of a failing/failed AOS (Air Oil Separator).

Regards, Maurice.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.