Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

alternator removal - help

carendt242
 Share

Recommended Posts

carendt242 Member

carendt242

Posted
Posted

once again, i agreed to help my friend work on his boxster (sans manual.) after checking the battery voltage, it looks like the alternator or voltage regulator is bad. i dug in but i'm stuck.

post-7824-1204844902_thumb.jpg

the green circle is a bolt on the deflection roller. i'm assuming i need to take this off to get to the alternator. however, the bolt will not come out. i turned it for about an hour today and, after coming out 1/2" or so, it doesn't seem to be coming ou anymore (it will turn.) rather than waste another hour, i thought i'd ask before turning it more. should the bolt come all the way out?

my other question: can i get away w/ just removing the deflection roller (assuming that bolt comes out) or should i relieve the belt via the tensioner? is the yellow circle the belt tensioner?

any help is appreciated.

thanks,

chuck

Link to comment
Share on other sites
1schoir Member

1schoir

Posted
Posted (edited)
once again, i agreed to help my friend work on his boxster (sans manual.) after checking the battery voltage, it looks like the alternator or voltage regulator is bad. i dug in but i'm stuck.

post-7824-1204844902_thumb.jpg

the green circle is a bolt on the deflection roller. i'm assuming i need to take this off to get to the alternator. however, the bolt will not come out. i turned it for about an hour today and, after coming out 1/2" or so, it doesn't seem to be coming ou anymore (it will turn.) rather than waste another hour, i thought i'd ask before turning it more. should the bolt come all the way out?

my other question: can i get away w/ just removing the deflection roller (assuming that bolt comes out) or should i relieve the belt via the tensioner? is the yellow circle the belt tensioner?

any help is appreciated.

thanks,

chuck

Chuck:

On a 986, you are only supposed to be able to loosen the bolt that you have circled in green by three (3) turns. Then, you must tap the bolt with a soft-faced hammer so as to loosen the bushing in the alternator arm. You have to continue tapping that bolt and bushing until the alternator can be slid off the bracket easily.

Then, after you remove the lower alternator bolt (about 7 o'clock on the face of the alternator), you can lift the alternator up and out of the slotted bracket along with the idler pulley. You may also have to turn the alternator clockwise to get it past the brackets and guide it out from under the intakes.

Note: I'm assuming that you have already removed the protective shield that is visible in your photo, just to the right (as you are facing the alternator from inside the car) and very slightly above the alternator .

Regards, Maurice.

Edited by 1schoir
Link to comment
Share on other sites
carendt242 Member

carendt242

Posted
  • Author
Posted
Chuck:

On a 986, you are only supposed to be able to loosen the bolt that you have circled in green by three (3) turns. Then, you must tap the bolt with a soft-faced hammer so as to loosen the bushing in the alternator arm. You have to continue tapping that bolt and bushing until the alternator can be slid off the bracket easily.

Then, after you remove the lower alternator bolt (about 7 o'clock on the face of the alternator), you can lift the alternator up and out of the slotted bracket along with the idler pulley. You may also have to turn the alternator clockwise to get it past the brackets and guide it out from under the intakes.

Note: I'm assuming that you have already removed the protective shield that is visible in your photo, just to the right (as you are facing the alternator from inside the car) and very slightly above the alternator .

Regards, Maurice.

thanks maurice - good thing i did not keep turning it for another hour :) now i only hope it goes back in!

i have not removed the protective shield - will do that next.

do i have to take the belt off? or will the tension of the belts be released once i move the alternator around?

thanks,

chuck

Link to comment
Share on other sites
1schoir Member

1schoir

Posted
Posted
thanks maurice - good thing i did not keep turning it for another hour :) now i only hope it goes back in!

i have not removed the protective shield - will do that next.

do i have to take the belt off? or will the tension of the belts be released once i move the alternator around?

thanks,

chuck

Chuck:

Not sure about the belt. When I replaced the alternator (also on a friend's car) we had already taken off the serpentine belt to replace that as well.

Regards, Maurice.

Link to comment
Share on other sites
boxs2000 Member

boxs2000

Posted
Posted

You must remove the belt. That is the easiest part : ) I had to slightly bent the lip of the opening to create enough room to get the alternator out as you spin it when removing. There is also a tread here that listed the part number for the voltage regulator. I was able to just get the voltage regulator through a MBZ dealer as they use the same one. (Porsche) does not sell it and its a Bosch part much cheaper than buying an alternator.

Link to comment
Share on other sites
carendt242 Member

carendt242

Posted
  • Author
Posted
On a 986, you are only supposed to be able to loosen the bolt that you have circled in green by three (3) turns. Then, you must tap the bolt with a soft-faced hammer so as to loosen the bushing in the alternator arm. You have to continue tapping that bolt and bushing until the alternator can be slid off the bracket easily.

i'm stuck (no pun intended) on this part. i see what looks like a bushing on the outside of the inner arm. if i take the bolt out, and shine a light through, i only see threads through the arm and nothing behind it.

should the bolt come out of the arm before tapping on it? so as to press the (rubber?) bushing i think i see? or should the bolt still remain in the threads while tapping it?

thanks,

chuck

Link to comment
Share on other sites
  • 1 year later...
GoodVibeGroove Member

GoodVibeGroove

Posted
Posted
On a 986, you are only supposed to be able to loosen the bolt that you have circled in green by three (3) turns. Then, you must tap the bolt with a soft-faced hammer so as to loosen the bushing in the alternator arm. You have to continue tapping that bolt and bushing until the alternator can be slid off the bracket easily.

i'm stuck (no pun intended) on this part. i see what looks like a bushing on the outside of the inner arm. if i take the bolt out, and shine a light through, i only see threads through the arm and nothing behind it.

should the bolt come out of the arm before tapping on it? so as to press the (rubber?) bushing i think i see? or should the bolt still remain in the threads while tapping it?

thanks,

chuck

I know this thread is old, but I just changed mine out yesterday, and the bushing IS the part with the treads, it is metal. I puonded on the bolt with a rubber mallet as others did, but I guess my bushing was really tight and that did nothing. What I finally did was just use a pry bar unde the alternator and pry the right side up. That did the trick just fine. Also, for anyone else doing this, DO NOT waste you time lossening the bolts for the air intake manifold lik I did! I thought by doing this I would have more roomto work with....which I did, but it added 2 hours to the job for no good reason! Live and learn I guess.....

Link to comment
Share on other sites
  • 8 years later...
Pigsypo Member

Pigsypo

Posted
Posted
On 2/2/2010 at 8:58 AM, GoodVibeGroove said:

I know this thread is old, but I just changed mine out yesterday, and the bushing IS the part with the treads, it is metal. I puonded on the bolt with a rubber mallet as others did, but I guess my bushing was really tight and that did nothing. What I finally did was just use a pry bar unde the alternator and pry the right side up. That did the trick just fine. Also, for anyone else doing this, DO NOT waste you time lossening the bolts for the air intake manifold lik I did! I thought by doing this I would have more roomto work with....which I did, but it added 2 hours to the job for no good reason! Live and learn I guess.....

 

New member here. I used your trick to use ply bar under the alternator to  get it slid off the bracket. When i try to turn the alternator CLOCKWISE to move the swivel arm close to the crackcase (as many of you suggested), i can't get it pass the fastening eye. I guess the bushing is still not "out" enough. any suggestions? i pounded and pounded for hours...

Link to comment
Share on other sites
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.