Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
Search the Community
Showing results for tags 'corrosion'.
Found 2 results
Long story short, one day noticed water in the drivers footwell, found a leak on the door to body wire harness. Dried car out. Car was 100% before this, seemed to be OK even when wet. 2 Weeks later, car started getting random faults on the MFI (Brake, ABS, PSM, etc). Would clear, then come, then clear. Battery is about 7 months old (replaced when I first got these errors) Ton of errors in durametric, then one day would not start or move out of if it did start. Peeled carpet back. Found 3 wires. 1 Crimped, 2 soldered. 1 of the soldered was gone, so cut that out, butt soldered and then repeated for the other 2 as I heard they usually go bad. Cleared all the DTCs with durametric, car started fine, all looked good in happyville. 2 weeks later got a check engine light, read codes, p0119, p0117 and p1552 (from memory, may be wrong). Seemed to be the engine temp sensor. Thought maybe a fluke, reset and ignored. This has been on and off last few months. I also noticed when hooking the durametric, or other code readers, it seemed to create a draw on the system, and the engine would idle rough, or the e throttle would not respond if I tried to drive with it plugged in. Pulled the durametric and all was fine, same with a bluetooth ODBII module I have. I replaced relay 433 under the driver's seat, and this seemed to cure that problem, since it provides relayed power to the CANBUS. About 3 months later got a PSM failure, at 45MPH and car went into limp mode. Restarted car, error was gone. Seemed fine for another month, got the same PSM failure yesterday, car seemed to be lurching a bit in slow moving traffic when it came up. Could the bad temp sensor be triggering this? It has slowly gotten worse I assume as once in awhile I see my gauge stops working. Or did I miss something else with my wire repairs. I am at the point ready to rip out passenger wiring under the carpet and inspect, but I suppose I should just replaced the impossible to reach temp sensor first, as it really does seem bad at this point. I also notice all the fuse block fuses for the PSM are on the right hand side, makes me wonder if the wiring issue is there. Just seems weird I have all these problems at once.
I spent the weekend on major maintenance: I attempted: 1. Cabin Filter (no issues) 2. Oil change (no issues) 3. Power steering fluid (question) 4. Front Rotor Change (no issues) 5. Brake fluid bleed (question) 6. Clutch fluid bleed (no issues) 7. Radiator and A/C Heat Exchanger clean-out (note of caution) 8. Spark Plug Change (major problem) 9. Cabin Filter (no issues) All parts were ordered from Sunset Porsche. Power Steering fluid: I could not figure out for the life of me what the purpose of the small rubber cap on the side of the reservoir? I just extracted what I could from the reservoir and then filled with Pentosin, started the car, turned the wheeel end-to-end several times and then repeated 5 times. I don't know if there's another way to swap the fluid. Brake Fluid bleed: (I used 1 liter) The instructions in one of the threads call to drain the outer caliper and then the inner. Why not the inner first because that is where the fluid source initiates it's entry into a caliper, i.e., line to inner caliper, line to between inner and outer caliper. Wouldn't it be logical to first drain inner so fluid is fresh in the inner chamber and then to drain the outer? Radiator and A/C Heat exchanger clean-out: Now I know what remover card is... I remember when I purchased the car, I could not for the life of me figure out what this plastic useless credit card was meant for. Now I know it's for the fog lamp housing removal. I used a credit card and it worked... The removal of the bumper is much easier than I thought, especially after repeating the removal twice because I forgot to plug the 'ambient temperature sensor connector' and I guess I didn't plug the side marker in all the way. Note of caution: be very careful when removing the connector and disconnecting the harness on the passenger side that links the bumper electrical. I snapped the locking connector and the tolerances are very tight so you have to cable tie it together. (electrical tape was not enough tension) On Sunday, one of neighbors asked if someone stole my wheel on Saturday night! You can see the connector for the Ambient Temperature Probe that I forgot to connect in the lower right hand corner... The red bucket is for scale. The driver side. I don't know why but the driver side was much dirtier than the passenger side. this images are after vacuuming but not before the water spray. Definitely a cure for OCD. You can see the salt tally on the fan housing. If you don't know, we salt our roads here in Michigan so if a surface is not treated, it will corrode. In this case it was mild surface accumulation, not brown rust. Spark Plugs: I read and re-read the articles on spark plug change. I can't remove the muffler because the bolts that clamps the connector between the muffler and exhaust manifold is completely rusted. Believe it or not, this is the only corrosion of fasteners on the car. (both sides) I'm going to grind the nuts and replace the faster: bolt, nut, washer combination. Anyone know the size? Are there any material scientists out there? If I were to grind this off and replace with a corrosion resistant fastener, which material should I use? I'm thinking of using a screw made from SS 300 that meets QQ-P-35 and meet FF-S-86 standards. Then again this material has to resist very high temp and stress from expansion of pipes. I'm also curious if anyone in California could check to see if there's is corroded? Ok, even if I could remove the bolts, how would you completely remove the muffler? If you see in this image, the bolt which loosened would lift up but it cannot due to interference from the body. there is no room to remove the coils because of the muffler mount. A view from the bottom: I"m wondering if anyone else has this working limitation. Last question: when the car ran without the ambient temp sensor attached, it faulted so now i have a 'visit Engine Center' on my start-up dash, error 17 = intermittent Amb Temp... How long before this disappears? Update: it disappeared this morning = 12 hours later. Thanks.