Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

DIY Convertible Top Window Repair


Recommended Posts

DIY Convertible Top Window Repair


This write-up describes a multi-step sewing and gluing process to repair a plastic window separating from the convertible top. See attached 9- page PDF file.   Window_Repair_DIY.pdf

 

Edited by frisbee91
Link to comment
Share on other sites

  • 9 months later...
  • 9 months later...

I'm having the same issue of separation. Honestly I don't want to try this method(I don't think I could do it cleanly). I stopped at a local shop yesterday and received a quote of $700.00 to re-sew the window. They said it was expensive due to it being labor intensive(taking top off and on). That seemed a bit excessive to me. I have a couple of questions:

1. Does anyone know a reputable shop in the North Dallas area they'd recommend for this type of repair?

2. This is probably a fools errand, but has anyone tried to replace the entire canvas themselves? I've found new complete tops for five to nine hundred dollars. I have the manual to take the top off, but it doesn't go into any detail about removing the canvas. If someone has done their own, how hard was it? who did you buy your top from?

Thanks in advance,

Allan

Edited by vfrpilot0
Link to comment
Share on other sites

It's not a fool's errand and it's definitely DIY doable, but you do need a lot of patience and a willingness not to cut corners. It takes about 6 to 8 hours to do the whole job, maybe a little more if you run into any roadblocks. Make sure that you have all the little parts you need before you start, including the double-sided tape. Someone also posted on here a couple of days ago that Pelican Parts sells a complete kit for the parts that are likely to have to be replaced, but I don't know what is in their particular kit.

Here's a DIY that is fairly comprehensive and easy to follow: http://sites.google....cingthetop-adiy

After reviewing the DIY, if you have any questions or need any clarification on any particular points, post here again and we'll get you through it.

Regards, Maurice.

Edited by 1schoir
Link to comment
Share on other sites

Thank you for the link to the article. It doesn't sound too bad really, but looks like it'd be easier with an extra set of hands. I'm going to continue researching before I jump one way or the other. The window itself is in decent shape. The rest of the top is is very good shape as well. I'm going to check a couple of other sources to see if I can just repair what I have first. If not, then I'll try to round up a buddy and try to tackle it myself.

I'm going to hop over to Pelican parts and see if I can find that link as well.

Regards,

Allan

Link to comment
Share on other sites

Brief update: It's been almost 2 years since I did this repair, and the stitching is holding up very well. The only change I would make would be to skip the use of the silicone caulk altogether. Instead, I'd use a heavy application of waterproofing spray on the seam.

Also, I have seen the "handy stitcher" sewing awl (or something similar) at Harbor Freight tools for cheap.

Link to comment
Share on other sites

  • 2 months later...

Brief update: It's been almost 2 years since I did this repair, and the stitching is holding up very well.

Do you have photos of the stitching? I'm a bit afraid to go that route without seeing how it might look.

With a good needle and (a lot of) patience, you can actually sew the stitches exactly into the original stitch holes and it will be completely undetectable.

Regards, Maurice.

Link to comment
Share on other sites

Brief update: It's been almost 2 years since I did this repair, and the stitching is holding up very well.

Do you have photos of the stitching? I'm a bit afraid to go that route without seeing how it might look.

The original window did not have stitching, so you can't just match the stitching holes. I used a piece of masking tape with marks every 3/16", and located the stitch line 1/4" from the edge of the plastic window. I don't have any current pictures of the window, but I could take another one later this week. There is a close up photo of the stitching in the pdf.

Link to comment
Share on other sites

  • 8 months later...

Brief update: It's been almost 2 years since I did this repair, and the stitching is holding up very well.

Do you have photos of the stitching? I'm a bit afraid to go that route without seeing how it might look.
The original window did not have stitching, so you can't just match the stitching holes. I used a piece of masking tape with marks every 3/16", and located the stitch line 1/4" from the edge of the plastic window. I don't have any current pictures of the window, but I could take another one later this week. There is a close up photo of the stitching in the pdf.

Frisbee91- firstly excellent DIY article.

I picked up the supplies for this project yesterday. My window is delaminated but not to the point where it has become unattached (like yours was). I am having a very difficult time folding over that 1/4" edge of canvas top that is supposed to be glued to the window. It is fighting me every inch of the way to the point where I don't think I would be able to clamp the whole bottom edge with one long board (as recommended in your DIY guide). I have the top in service mode and the cables unhooked. I saw your comment about the top being "partially deployed during the gluing process to relieve stress". Is that different then having in in full service mode with the cabes unattached? Any guidance is appreciated. Thanks again for taking time to document your process.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.