Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

Recently, on my 98' Boxster (mileage 90 K) the CEL came on and from my Durametric reader, code P0446, Porsche fault code 95 [shutoff valve activated / charcoal filter] was displayed. Can anyone explain what this means and what do I (from a DIY perspective) need to do? Thanks!

Link to comment
Share on other sites

You need to get the full set of Porsche service manuals including the OBDII and Diagnostic manuals. You can contact me about that. As to your code see below. I copied most of the information for you and attached the pages from the DME 5.2 manual. Obviously this is only for educational purposes.

P0446 95 EVAP Canister Shutoff Valve (Function) – Below Limit

 

 

20 93

 

P0446

 

95 EVAP Canister Shutoff Valve (Function) – Below Limit

 

Function

 

The task of the shutoff valve is to seal the purge air line to the EVAP canister during the fuel tank leak test.

 

Diagnosis conditions

 

– Oxygen sensing system active

 

– No secondary air

 

– No secondary air diagnosis

 

– Air mass < 30 kg/h

 

– Engine running

 

– Vehicle speed = 0 km/h

 

– Intake air temperature between –12 °C and 60 °C

 

– Battery voltage > 11 V

 

– Engine load < 2.4 ms

 

– The vehicle must not be at an altitude of above

 

2448 m

 

– Time elapsed after engine start-up > 990 sec.

 

– No faults in: Throttle position sensor, idle air

 

control, load sensing, misfire detection, vehicle

 

speed, EVAP canister purge valve, idle air control

 

valve, mass air flow sensor, voltage supply,

 

pressure sensor, shutoff valve and engine

 

temperature

 

DTC No. Fault conditions Fault area

 

P0446 Below lower limit – Purge air line blocked

 

– Flow resistance of EVAP canister too high

 

Note

 

Fuel tank ventilation can be activated with the Porsche System Tester 2 in the Short test menu.

 

On-Board Diagnostic Boxster Troubleshooting

 

1999 Supplement 3 P0446 - 1

 

System Overview

 

673_97

 

1 – EVAP canister purge valve

 

2 – EVAP canister

 

3 – Purge air

 

4 – Tank

 

5 – Pressure sensor

 

6 – Shutoff valve

 

7 – Operating purge valve

 

8 – To intake manifold

 

9 – Vacuum control valve

 

6

 

Troubleshooting Boxster On-Board Diagnostic

 

P0446 - 2 Supplement 3 1999

 

Diagnosis Procedure

 

1 Check purge air line for blockage.

 

OK

 

Repair purge air line.

 

End

 

Replace EVAP canister.

 

End

 

Not OK

 

On-Board Diagnostic Boxster Troubleshooting

 

1999 Supplement 3 P0446 - 3

 

1 Check purge air line for blockage.

 

1. Remove front right-hand wheel housing liner.

 

2. Detach purge air line (connection face up) from

 

EVAP canister.

 

3. Blow through purge air line with compressed air.

 

Troubleshooting Boxster On-Board Diagnostic

P0446

 

986 DME 5.2 P0446.pdf

Link to comment
Share on other sites

  • 6 years later...

There is a 'shut off' valve with electric plug on it, top front of charcoal canister which I changed along with the pink valve on top of canister (maybe called purge or vent valve) a double type valve about 3 months ago. CEL still comes on. That's why I am really interested in this blue thing on the side of the canister. It does NOT have an electric plug to it.   I disconnected the pipe top from the pink vent thing and the bottom with the blue plastic type round valve set in the middle of this length.  I held the pipe in my hands and can blow each way past this valve with ease. I would have thought I could only blow one way as a kind of a one way valve thing but NO.  Is the thing GOOD or BAD? Whats this for?. Why is it there?. What is the name of the thing?. I seem to remember someone said it is a 'check valve' but it doesn't seem to check anything only my patience as far as I can tell. I put the part # on google NOTHING. Oh yeh some bloody oil well in Texas somewhere came up. Very helpful lol.

Edited by Hurdigurdiman
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.