Jump to content

The RennTech.org community is Member supported!  Please consider an ANNUAL donation to help keep this site operating.
Click here to Donate

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)


Contributing Members
  • Content Count

  • Joined

  • Last visited

Everything posted by EleCTriCT

  1. Hi All, 2006 Cayman S The lower left stalk on the steering column is not functioning. The one that controls the OBC/MFA/GRA or whatever you prefer to call it? Basically you cant check the oil level is the problem and the switch is un-responsive to anything. any tips??
  2. Hey Everyone, 1999 996 C2 Cab Does anyone have a picture or diagram for installing a new clam shell motor - comes with an update kit with new mount bracket etc. Looks like the old piece needs to cut off and the new section fitted and bolted/welded. Cheers.
  3. a quick google search bring up this.. which i have successfully installed before for someone. http://www.vertexauto.com/cayenne-drive-shaft-repair-clamping-support-mount-p-10391.aspx i'm pretty sure porsche does not sell the support bearing only a complete shaft, hence the aftermarket solution. cheers
  4. Update - we ran a tranny calibration with the pwiz and ended up clearing the faults with an aftermarket scanner... For whatever reason the faults would not clear with the P Scanner. Test drive and Faults have not returned yet....
  5. So I have a PDK fault that wont clear, p18C0 <-- havent seen this one before and cant pull up any info. Resulting in no sport mode, psm faults and corresponding dme fault. As always any input is appreciated. Cheers!
  6. There is apparently a method of filling the entire system from r/f strut pressure line.... does anyone know if there is a service port or will i have to create some sort of adapter?
  7. Greetings 2010 Panamera 4S Fault... PASM Fault: 000315 - Level Control Switched OFF / Jack mode on. (Hard Fault wont clear...) Symptoms... Height Control Button on consol innop... Front end all the way down... Rear End all the way up... Sport Mode features Innop due to PASM Fault.... Any ideas? cheers!
  8. So the "Pressure Sensor" is bolted to the inside of the inner door panel of the drivers door. the vehicle had a broken wire in the door jamb - causing the intermittent fault - the wire was repaired and the sensor was still replaced for good measure since the door was all apart. cheers
  9. I think More importantly im looking to find out if this is for the igniter in the seat or the impact sensor on the floor pan? the fault was pulled with a Piwis Tester II and im not familiar with the "pressure sensor" wording thanks!
  10. Hi All, Just looking for some more information on the following. 2011 cayenne 3.6L B101713 - Drivers Side - Side Airbag - Pressure Sensor, Open Circuit Thanks kindly!
  11. i recently fixed this issue on a gen 1 boxster by recoding the module. everything was coded except for the country. selected USA and viola rear trunk release started working via remote. piwis was used
  12. up here where we get frost it is far more noticeable because the wheels get to slip on the pavement - even the cayenne shudders at full lock etc. geometry limitations imho
  13. Thank you. In my situation the sensor was lying on the block - most likely getting to much heat. Cheers
  14. Can anyone help identify the Engine Compartment Fan Temp Sensor Location on the Twin Turbo? It must be a little more hidden than on the NA cars. Thanks.
  15. Boom! Hero Status Achieved! That was the trick, glass released no problems!!!!
  16. Anyone have experience removing the side mirror glass to access the screws to take apart the trim?? Parts Diagram Maybe? Thanks in advance.
  17. Hi there, could I please get the code for cdr-220 and y5050583 Thank you
  18. the o2's have 4 wires, the heater circut is the 2 white wires. you can verify the vehicle side has voltage and verify the o2 sensor has resistace on the heater circut. cat efficiency fault is often the cat itself. hope this helps
  19. a quick search pulls up the following.... P0430 Toyota - Catalyst System Efficiency Below Threshold Bank 2 What is your faults description? model toyota?? In my experience the cat is actually commonly the problem with these faults.
  20. Remove bezel red dots in photo show screw locations there may be 2 or so hard to see screws underneath to the left of my hand. cluster has 2 screws on each side afterwards i think there is 3 connectors on the back, brittle fragile connectors be careful cheers
  21. I Concur, I believe last time I saw this issue a "Handover" Solved it (Requires capable shop equipment)
  22. Hey everyone, Working away on a 2009 Cayenne S - CEL not on, but code "3505" scanned with durametric with no description. other modules such as TIP / PSM have "1341" Codes refering to check the DME Any tips appreciated Cheers! D. PS I noticed the low oil warning was on due to 1L shy of oil... Thanks
  23. awesome thanks for the help! that seems pretty useless ill probably suggest sending that back
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.