Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

RMS & IMS tools


Recommended Posts

I'm going to be replacing the engine in my '99 Boxster (thread about engine replacement) with a used engine. To get maximum reliability without spending $15k+ on a bullet-proof engine, I'm going to replace the RMS and do the IMS retrofit using the LN Engineering bearing. I may also replace the AOS and the water pump.

I know that replacing the RMS can be a bit tricky as if you push it in too far, it will pop inside the case, and that would be a very bad thing. I also know that the IMS retrofit requires a few specialty tools. Does anybody have the tools to properly do these jobs that they'd be willing to either rent to me, or sell me used? As I mentioned in my other thread, I really need to very carefully manage my budget on this project, and I'd really rather not spend $200 or so on tools that I will use for one job and never use again. So if you've done the job, and spent the money on the tools, I figure this is a way you can recover some of that money, and I can save some money. A win-win.

Link to comment
Share on other sites

  • Moderators

You may luck out and find someone to help you with this, but the reality of Porsche specialty tooling is that most purchasers are not going to loan or rent out these items. We get this type of request all the time, and we always respectfully decline for a variety of reasons…………

Link to comment
Share on other sites

You might buy the bearing with tools from LN Engineering, then sell the tools online when you are done. I know I'd be interested in a set, since I can guess to be replacing the clutch and bearings in about a year.

Yeah. However, I figured maybe somebody has already done it and doesn't need the tools anymore. Maybe not, but I had to ask.

Link to comment
Share on other sites

The tool to pull the IMS bearing is $70 from LN Engineering and the installation tool comes with the bearing kit. You will need something to remove/reinstall the RMS though.

I only see the tool on this page (My link) and it's listed for $136. I guess I have to call them. Still hate to spend $70 on a tool that I will only use once. Oh well.

Link to comment
Share on other sites

The tool to pull the IMS bearing is $70 from LN Engineering and the installation tool comes with the bearing kit. You will need something to remove/reinstall the RMS though.

I only see the tool on this page (My link) and it's listed for $136. I guess I have to call them. Still hate to spend $70 on a tool that I will only use once. Oh well.

Wow, they stepped up their game with the extraction kit...it used to just be the puller tool for $70, but now they include cam locks and other useful things. Can't hurt to be too careful, though it costs twice as much...

Edited by Dr.Strangepork
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.