Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
By Mark Stubbs
Hi guys.Finnally got the Boxster on the road after an enforced year stood.It sounded a bit rattly when I started it up.I have done about 50 miles in it since all short journeys, and it still making the same noise.Not knowing much about these engines not sure if it's something more serious than tapped, alternator bearing???.Im not driving it and will get it recovered to an Indy for assessment, so any suggestions will be gratefully received. Hopefully other club members will chime in.
Late 2004 Boxster Base Tiptronic with 45,000 miles
I have racked up 15,000 miles over the last 3 years of ownership. The coolant was flushed about a year prior to purchase. I think it's time to flush the coolant. I plan to buy the Airlift tool - it's a time vs cost issue, time wins.
I know from searching that JFP has recommended to others to replace the water pump as preventative maintenance on a car this age. Fair enough. Porsche pump, clean the mating surfaces carefully and:
1. Use gasket sealant or no sealant?
2. Should I replace the coolant reservoir even though I cannot find anything wrong with it?
I'll replace the thermostat at the same time.
3. Should it be the 160 degree thermostat?
3a. I notice that the car runs between 190 - 210 degrees (using Scangauge) most of the time in warm weather, so will the 160 stat be a benefit?
4. Which hoses should be replaced?
5. Anything else?
Since the start of ownership I've done mostly preventative and general maintenance with very few actual failures of any kind. With that being said, I think mileage is beginning to expose some common failures cropping up like what happened yesterday - the turn signal stalk won't hold in-place, so now I need to replace it but at least getting the 4-stalk version will give me the OBC functions.
X-posting from other forums as this seems to be a rare issue?
Car is 2010, C2, PDK
Has anyone had this issue?
I have read a post or two where people were just leaving things be.
Would appreciate getting any feedback on what could be the cause. I have checked the power steering fluid, and it was full.
The video is of the rack itself.
By Alan Huey
I recently had to replace the water pump on my 2001 Boxster. This all went fine, however, the red light to the right of the temperature gauge is blinking at 1 Hz. I've read this indicates low coolant level. I followed the factory procedure to bleed the system and it is filled to the max, but the light still blinks. Also, the gauge is flatlined to the left. I replaced the temperature sensor near the #4 cylinder head without improvement, and the wires "look" ok. All the fuses are good. Does anyone know the procedure to troubleshoot this wiring? Or the pin and socket numbers for the wiring diagram? The temperature gauge worked fine before the water pump blew up. I did recover most of the impeller, but a few small pieces are in there.